Synchronizing a project drawing with AEC standards
Two lists are displayed. The top list shows styles and display settings that have corresponding styles or
display settings in the project standards, but are either an older version of a standard style or display setting,
or a nonstandard (newer) version. The bottom list shows a list of styles and display settings that do not
have corresponding styles or display settings in the standards (not standardized styles and display settings).
For a definition of the terms, see “
Project Standards Terminology
” on page 332.
3
To synchronize a style or display setting that is either an older version or a nonstandard (newer) version,
select Update from Standards from the Action drop-down list.
4
To skip over a style or display setting that is either an older version or a nonstandard (newer) version, select
Do not Update from the Action drop-down list.
In this case, the nonstandard version remains in the project drawing for now, and is not updated with the
standard version. The next time the drawing is synchronized, the style or display settings will be listed
again as older version or nonstandard version.
5
To ignore a style or display setting that is either an older version or a nonstandard version, select Ignore
from the Action drop-down list.
In this case, the nonstandard version will not be listed again in future synchronizations, except if you select
Show objects set to ignore during project standards synchronization, or remove the Ignore flag from the
style or display setting in Style Manager or Display Manager, as described in “
Excluding Styles and Display
Settings from Synchronization
” on page 368.
You should use the Ignore option only in clearly defined exception cases where you are sure that a style
or display setting does not need to conform to the project standards.
6
To skip over a not standardized style or display setting, select Skip from the Action drop-down list.
The next time the drawing is synchronized, the style or display setting will be listed again as not standardized.
NOTE You cannot promote not standardized styles and display settings to standard ones here. To do this, you
need to add the not standardized style to the project standards, as described in
“
Adding Standard Objects from
a Project Drawing to a Project Standards Drawing
” on page 379
.
7
To ignore a not standardized style or display setting, select Ignore from the Action drop-down list.
In this case, the not standardized object will not be listed again in future synchronizations, except if you
select Show objects set to ignore during project standards synchronization, or remove the Ignore flag from
the style or display setting in Style Manager or Display Manager, as described in “
Excluding Styles and
Display Settings from Synchronization
” on page 368.
8
Click OK.
Synchronizing Selected Styles and Display Settings with AEC Standards
You can synchronize individual styles and display settings in Style Manager and Display Manager. You could do this
if you have accidentally changed a style in the project drawing, and want to restore the correct version from the project
standards. Synchronizing an individual style or display setting will take less time than synchronizing a drawing or the
project.
364 | Chapter 7 Project Standards
Summary of Contents for 00128-051462-9310 - AUTOCAD 2008 COMM UPG FRM 2005 DVD
