Automated Logic ZN551 Technical Instructions Download

Page: 15 / 18

Ack Required for Off-Normal,
Fault, and Normal

Requires a control module acknowledgement for each
message type. Normally not required.

TIP

To require operator acknowledgement for an Alarm

or Return-to-normal message (stored in the WebCTRL
database) change the acknowledgement settings on
WebCTRL's

Alarm > Enable/Disable

tab for an alarm

source or an alarm category.

Recipient List

Recipients

The first row in this list is the WebCTRL Server. Do not
delete this row. Click

Add

if you want other BACnet

devices to receive alarms.

Recipient Description

Name that appears in the

Recipients

table.

Recipient Type

Use

Address

(static binding) only for third-party BACnet

device recipients that do not support dynamic binding.

Recipient Device Object
Identifier

Type the

Device Instance

from SiteBuilder (or from the

network administrator for third-party devices) in the

field.

Process Identifier

Change for third-party devices that use a BACnet Process
Identifier other than 1. WebCTRL processes alarms for
any 32-bit Process Identifier.

Issue Confirmed
Notifications

Select to have a device continue sending an alarm
message until it receives delivery confirmation from the
recipient.

Common Alarms

On these pages, you can change the following control module alarm
properties:

•

BACnet alarm object properties

•

Enable/disable

•

Delays

NOTE

To set up alarm actions for control module generated alarms, see

Setting up alarm actions

in WebCTRL Help.

Module Generated Alarm

Description

Short message shown on WebCTRL's Alarm page or in an
alarm action when this type of alarm is generated.

Events

Alarm Category and Alarm
Template

See

Customizing alarms

in WebCTRL Help.

Enable

Clear these checkboxes to disable Alarm or Return to
normal messages of this type from this control module.

Notification Class

Do not change this field.

Custom Translation
Tables

On the

Custom Translation Table

pages, you can edit the tables used to

translate raw sensor data to engineering units for inputs associated with

Non-Linear, Custom Table

sensor/actuator types.

ZN551 Control Module • Rev. 3/17/2005

Summary of Contents for ZN551



















Search results

Summary of Contents for ZN551

Reviews:

Related manuals for ZN551

Brands by name

Popular brands

Automated Logic ZN551, Technical Instructions

Search results

Summary of Contents for ZN551

Reviews:

Related manuals for ZN551

Brands by name

Popular brands