background image

2

Table of contents

1 -  SYMBOLS USED IN THE MANUAL

Pay special attention when reading this manual to the parts marked by the symbols:  

NOTE!
Suggestions for the user

ATTENTION!
Possible hazardous situation 
for the product and the environment

DANGER!
Serious danger for 
personal safety and life

2 -  APPROPRIATE USE OF APPLIANCE

The FIREX 

appliance has been built according to the current level of engineering and acknowledged 

technical safety rules.

 

Nonetheless, if improperly used, dangers could arise for the safety and life of the user and other persons 
or damage to the equipment or other objects. 
The appliance is intended to operate in hot air circulation heating systems. Any other use must be considered 
improper. 
Firex shall not be held liable for any damage resulting from improper use; in this case the user is fully 
responsible for the risk. 
Use according to the intended purposes also includes careful compliance with the instructions in this manual.

3 -  WATER TREATMENT

•  The hardness of the feed water conditions the frequency at which the domestic hot water producer must be 

cleaned.

•  If the water has a hardness greater than 15°f, we recommend using water softeners, chosen according to the 

characteristics of the water.

•  We recommend checking and cleaning any installed domestic hot water exchanger at the end of the fi rst 

year of use and every two years thereafter; on this occasion, also check the state of wear of the anode.

TABLE OF CONTENTS

1  Symbols used in the manual ..................................................................................................................................................... 2
2  Appropriate use of appliance ................................................................................................................................................... 2
3 Water 

treatment 

......................................................................................................................................................................... 2

4  Information provided to the user by installer/maintenance technician .................................................................................. 3
5 Safety 

warnings 

......................................................................................................................................................................... 3

6 Operating 

instructions............................................................................................................................................................... 4

6.1  Standard panel board ......................................................................................................................................................... 4
6.2  Checks before commissioning .......................................................................................................................................... 6
6.3 The wood ............................................................................................................................................................................ 7
6.4 Wood humidity 

.................................................................................................................................................................... 7

6.5 Dimensions ......................................................................................................................................................................... 7
6.6 Start-up ............................................................................................................................................................................... 7
6.7  Combustion air adjustment ................................................................................................................................................ 8
6.8  Checks to be carried out after commissioning ................................................................................................................. 9
6.9 General warnings 

.............................................................................................................................................................. 10

6.10  Summer mode ................................................................................................................................................................ 10
6.11  Maintenance ................................................................................................................................................................... 11
6.12  Troubleshooting .............................................................................................................................................................. 12

Summary of Contents for Firex 34













Reviews: