Automatic Products 310 Operating & Service Manual Download

Page: 12 / 100

2.01

The 115 VAC power cord from the wall outlet comes into
the machine and plugs into the back of the main junction
box located on the top center of the cabinet. The voltage
output to the board is 24 volts and 8 volts and is plugged
into Logic Center Board.

Lighting System

There are two fluorescent lamps in the APi 320 Series
machines. The lamps are located vertically on the inside
of the door along the edge of the outer glass which light
up the main product area. The starter is located on the
underside of the bottom lamp socket of each lamp. Each
lamp is covered by a plastic shield.

Main Product Shelves:

There are a maximum of five main product shelves per
machine. Each selection has its own motor mounted to
the back of the shelf. Every shelf has its own harness and
plug for connecting to the remainder of the circuit through
the cabinet receptacle, located in the rear right of the
cabinet. You also have the capability to adjust each shelf

⁄

inch either up or down on any shelf. To do this the shelf

should be removed and the cabinet back harness
receptacle lowered or raised with the right & left shelf
tracks.

Note:

When exchanging the shelves, you will not need

any parts but you will have to reprogram the machines for
prices and selections.

Removal of Product Shelf:

A. Lift up and push the lock levers toward the back of

cabinet.

B. Pull the shelf to its loading position.
C. Grasp shelf in front and rear center. Lift front of shelf

up above horizontal and pull shelf forward while lifting.

D. To install shelf, reverse above procedure.

Delivery Bin

This is located below the display window on the door and
is mechanically operated. The linkage on the outside end
of the delivery bin may require occasional lubrication.
Should the door become difficult to operate, place a small
amount of grease on the arm tracks.

Removal of Delivery Bin:

A. Remove the screws from the sides of the
delivery bin.
These screws fasten into the lower door

brace and remove the two screws and

brackets at the

top of the delivery bin.

B. Grasp delivery bin on both sides and lift upand pull

back. Should the bin be tight, rock it by lifting on one
end, then the other.

Replacement of Delivery Bin:

A. Locate lip on front edge of delivery bin
over lower edge of opening in door and
behind trim. Press down

along lip to make sure it is fully engaged

between door and trim.

B. Install the four screws and two brackets, to secure bin

to door.

Heated Glass

The glass on the inner door is a double pane, heated,
thermal pane. There is a connector on the bottom right
hand side of the glass. The glass receives power for the
heater strip through this connector from the junction box.

DEX/UCS

The APi 310 supports DEX/UCS Communications
Protocol - NAMA Vending Industry Data Retrieval
Standard.The machine will automatically recognize the
DEX/UCS device when it is plugged into the control board
and will recognize when the device initiates the
communication protocol.The transmission/reception of
data to the device will then take place automatically.

Baffle Door

The baffle door is located above the delivery bin and
extends out from the bottom of the main product area.The
purpose of the baffle door is to seal the area between the
refrigerated cabinet and the delivery bin. Each time a
selection is made the baffle door is opened before the
product is delivered and is closed after the product has
been delivered.The baffle door is opened and closed by a
motor mounted toward the back left hand side of the
machine just above the compressor. The baffle door can
be re-opened one time after a vend by pressing the
coin return.

The Chime

The chime will sounded when the following events occur:

•

Three times when an invalid key sequence is entered
from either the front panel or the MasterMenu™
Keypad.

•

Three times when the customer enters an invalid key
sequence from the front panel.

• Five times when the customer has won a free vend

due to WINNER MODE.

• Five times when the customer attempts to purchase a

sold-out item as determined by spiral selection.

• A single time to indicate the acceptance of an action

by the control system.

Power Interlock Switch

The interlock switch is located on the bottom right corner
of the machine. When the door on the machine is open
the interlock breaks the power (hot and neutral) going into
the refrigerated cabinet control box. Power for the FDB
comes from the LCB via the interconnect harness and
this power is not interrupted by the interlock switch.

components