Automatic Solutions CTR50 Installation Manual Download

Page: 17 / 22

ELECTRICAL AND MECHANICAL SPECIFICATIONS

Dimensions and weight (with plastic box)

: 186 x 283 x 112 mm – 2.3 Kg

Power supply transformer

: 230/12-15-20 Vac - 100VA

Battery-charger capacity

: 0.5 A max

Optional battery capacity

: 12/24 Vdc – 7 Ah

Blinker power supply

: 12/24 Vdc - 15W max

Relays contacts capacity

: 20 A max

Electric lock power supply

: 12/24 Vdc - 15W max

Motor power supply

: 12/24 Vdc - 100W max (total)

Radio receiver power supply (J6)

: 12 Vdc - 2W max

Accessories power supply

: 13,5Vdc or 24Vdc - 3W max

Operating temperature range

: 0 to + 60 °C (internal)

radio channel relay contact characteristic

: 24 Vac – 0.5 A max

Motors’ work time

: programmable, 1 to 120 sec.

Pause time

: programmable, 1 to 120 sec.

wing closing delay

: programmable, 0 to 120 sec.

Amperometric Stop

: Automatic

Caution:

The unit must be not switched on if the connected loads or the power supply exceed the limits. Failure to observe this precaution

can result in damage to persons, animals or objects for which the manufacturer cannot be held responsible.

ELECTRICAL CONNECTIONS

7 electric connectors are fitted to the card:

10-pole removable terminal board for the connection of the commands and safety devices

10-pole connector for the optional connection of a radio receiver card

2-pole Terminal board for the connection of the aerial cable

10-pole removable terminal board for the connection of the power devices

8-pole removable terminal board for the connection of the limit switches and/or Encoder

FS1,FS2

nr. 2 Faston terminals for the connection of a Backup battery

FS3,FS4

nr. 2 Faston terminals for connection of the power supply transformer

Terminal board J2

Terminal1 - Common terminal for all electric contacts of commands

Terminal2 - Pedestrian start push-button’s normally open electric contact

Terminal3 - Start push-button’s normally open electric contact

Terminal4 - Common terminal for all electric contacts of stop push-button and photo-cell

Terminal5 - Emergency push-button’s normally closed electric contact (stop)

Terminal6 - Photo-cell’s normally closed electric contact

Terminal7 - Common terminal for the electric contact of photostop

Terminal8 - Photoelectric cell’s normally closed electric contact (photostop)

Terminal9 - 2nd radio-channel’s normally open electric contact (output)

Terminal10 - 2nd radio-channel’s normally open electric contact (output)

Important: The normally closed inputs not in use must be fitted with jumpers

Connector J6

Terminal1 – Normally open electric contact connected to the start

Terminal2 – Common of the normally open electric contact connected to the start

Terminal3 – Normally open electric contact connected to the 2nd radio-channel output

Terminal4 – Normally open electric contact connected to the 2nd radio-channel output

Terminal5 - Power supply negative (common)

Terminal6 - Power supply positive

Terminal7 - Power supply positive

Terminal8 - Power supply negative (common)

Terminal9 – Aerial input (shield)

Terminal10 – Aerial input (signal)

Summary of Contents for CTR50























Search results

Summary of Contents for CTR50

Reviews:

Related manuals for CTR50

Brands by name

Popular brands

Automatic Solutions CTR50, Installation Manual

Search results

Summary of Contents for CTR50

Reviews:

Related manuals for CTR50

Brands by name

Popular brands