background image

P. 6

 User 

Guide

 

 

Quick Lockout

TM

 

(Also called 

secure panic

.) For fast protection in emergency situations, the system will 

LOCK

 all 

doors when you 

press the brake pedal while you hear the sound signal

. (

Quick lockout

 is only 

available when 

panic mode

 has been set off.) 

Cold Weather Mode 

When cold weather mode is active, the engine starts every 2 hours and runs for 3 minutes (or for 8 
or 20 minutes with diesel engines). Cold weather mode automatically ends after 24 hours. 

To enter Cold Weather Mode: 

 

Press the 

SHIFT

 button and then the 

START/STOP 

for 3 seconds

 

There will be two (2) beeps and the parking lights will flash three (3) times. 

To exit Cold Weather Mode, do any one of the following actions: 

 

Open the hood.  

 

Start the engine by remote. 

 

Turn the ignition key to the 

IGNITION ON (RUN)

 position. 

 

Press the 

SHIFT

 button and then the 

START/STOP

 button for three seconds. 

There will be one (1) beep and the parking lights will flash once. 

To verify whether the system is in cold weather mode: 

  Press and release the brake pedal: 

  If the vehicle is in cold weather mode, the parking lights will stay on while the pedal is pressed. 

Extended Run Time 

While the vehicle is running under a remote start, 

pressing and holding the 

START/STOP

 button 

for more than 3 seconds 

will reset the run time counter to zero and restart the run time cycle from 

the beginning.  There will be one beep 

a pause

 three more beeps; the parking lights will flash 

three times and the horn (if configured) will honk once. 

The extended run time procedure can 

only be carried out once per remote start.  

  

To stop the vehicle, at any moment, simply press the 

START/STOP

 button.  

Example:  

If your remote car starter is programmed for a run time of 3 minutes and your vehicle 
has been running for 3 minutes already, pressing the 

START/STOP

 button will reset the 

counter to zero and allow the engine to run for another cycle (in this case, 3 minutes). 

Summary of Contents for ANT-4420















Reviews: