background image

P. 14

  

Installation 

Guide

 AS-1785

 

Table 4: Accessing options 

In each Function, once an Option has been selected the Parking Lights will flash 1, 2, 3 or 4 times 
(depending on the selected Option). 

Please note 

that the different Functions within any particular Mode can only be accessed 

sequentially: the Programming Centre will move from Function 1 to Function 2, then to Function 3, 
and so on. Therefore, whenever you access a particular Mode, be prepared to re-configure all the 
Functions of that Mode in ascending order. 

Programming Options 

MODE 1

 

 

* INDICATES DEFAULT SETTING 

FUNCTION 1 – Ignition-controlled Door Locks 

OPTION 1* 

Ignition Lock 

DISABLED

 

 

OPTION 2 

Ignition Lock 

ENABLED

 

OPTION 3 

Ignition 

UNLOCK ONLY

 

OPTION 4 

Ignition 

LOCK ONLY

 

FUNCTION 2 – Secure Lock  

OPTION 1* 

Secure Lock 

DISABLED

 (1-sec. Disarm pulse) 

OPTION 2 

Secure Lock 

ENABLED

 in Smart Mode 

OPTION 3 

Secure Lock 

DISABLED

 (1/2-sec. Disarm pulse) 

OPTION 4 

Secure Lock 

ENABLED

 in Standard Mode 

FUNCTION 3 – Passive or Active Arming 

OPTION 1*

 

PASSIVE 

Arming (60 sec.) 

OPTION 2 

ACTIVE

 Arming  

OPTION 3

 

PASSIVE 

Arming (3 min.) 

FUNCTION 4 – Door lock pulse timing 

OPTION 1* 

7/10-sec. Lock/Unlock pulses 

OPTION 2 

4-sec. Lock/Unlock pulses 

OPTION 3 

7/10-sec. Lock pulse and two 1/4-sec. Unlock pulses 

OPTION 4 

1/10-sec. Lock/Unlock pulses 

FUNCTION 5 – LED flashing 

OPTION 1* 

ENABLED

 (without starter kill 

Æ

 will flash only when ignition is OFF)  

OPTION 2 

DISABLED

  

OPTION 3 

ENABLED 

(

with starter kill 

Æ

 will flash when the starter kill engages. 

 

This option should be selected 

ONLY

 if the starter kill is installed.) 

 

 

 

MODE 2

 

 

* INDICATES DEFAULT SETTING

 

FUNCTION 1 – Safe Start. 

OPTION 1

 

Safe Start 

ENABLED

 

OPTION 2* 

Safe Start 

DISABLED

 

OPTION 3 

“Swap Start” – enhanced Safe Start Mode with extended safety: 

  

To start the Engine: press the 

LOCK

 and 

UNLOCK

 buttons simultaneously 

  

To trigger 

AUX 2

: press the 

START

 button 

FUNCTION 2 – Engine Run Time 

OPTION 1

 

Run Time = 4 minutes in 

GAS

 mode / 9 minutes 

DIESEL

 mode 

OPTION 2* 

Run Time = 15 minutes in 

GAS

 mode / 20 minutes 

DIESEL

 mode 

OPTION 3 

Run Time = 25 minutes in 

GAS

 mode / 30 minutes 

DIESEL

 mode 

Summary of Contents for AS-1785

























Reviews: