Installation Guide
P. 17
2.
Before the lights go out, press and hold the brake pedal and then press one of the following
buttons:
LOCK
...............................to access menu 1;
UNLOCK
...........................to access menu 2;
TRUNK
…………………… to access menu 3; or
START/STOP
...................to access menu 4.
3.
The parking lights will flash and the horn will honk (if programmed) once, twice, three or four
times to confirm entry into a menu.
4.
Release the brake pedal.
Once the desired menu has been selected, the unit will fall (by default) into feature #1 of that
menu; you can now select the option you want in feature 1. Once this option has been chosen, the
unit will move on to feature 2 of the menu selected, and so on.
LOCK
for
Option 1,
UNLOCK
for
Option 2,
TRUNK
for
Option 3;
START/STOP
for
Option
4.
Programming Options
MENU 1
* INDICATES DEFAULT SETTING
FEATURE 1 – Ignition-controlled door locks
OPTION 1*
Ignition lock
DISABLED
OPTION 2
Ignition lock
ENABLED
OPTION 3
Ignition unlock only
OPTION 4
Ignition lock only
FEATURE 2 – Secure Lock
OPTION 1*
Secure lock
DISABLED
OPTION 2
Standard secure lock
ENABLED
OPTION 3
Smart secure lock
ENABLED
FEATURE 3 – Starter kill arming mode
OPTION 1*
Passive arming (60 sec.)
OPTION 2
Active arming
OPTION 3
Passive arming (3 min.)
FEATURE 4 – Door lock / unlock pulse timing
OPTION 1*
7/10-sec. lock / unlock pulses
OPTION 2
4-sec. lock / unlock pulses
OPTION 3
7/10-sec. lock pulse and two 1/4-sec. unlock pulses
OPTION 4
1/10-sec. lock / unlock pulses
FEATURE 5 – LED flashing
OPTION 1*
ENABLED
(without starter kill
Æ
will flash only when ignition is OFF)
OPTION 2
DISABLED
OPTION 3
ENABLED
(with starter kill
Æ
will flash when the starter kill engages.
This option should be selected
ONLY
if the starter kill is installed.)
MENU 2
* INDICATES DEFAULT SETTING
FEATURE 1 – Safe Start
OPTION 1
Safe Start
ENABLED
OPTION 2*
Safe Start
DISABLED
OPTION 3
“Swap Start” – enhanced safe start mode with extended safety: To start the engine: press
F
then
LOCK
buttons. To trigger
AUX
2
: press
START/STOP
button.
FEATURE 2 – Engine Run Time
OPTION 1
Run Time = 3 minutes in
gas
mode / 8 minutes
diesel
mode
OPTION 2*
Run Time = 15 minutes in gas mode / 20 minutes diesel mode
OPTION 3
Run Time = 25 minutes in
gas
mode / 30 minutes
diesel
mode
FEATURE 3 – Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)
OPTION 1
Idle mode & turbo mode
DISABLED (AUTO)
/ turbo mode
DISABLED (MANUAL)
OPTION 2*
Idle mode & turbo mode
ENABLED (AUTO)
/ turbo mode
DISABLED (MANUAL)
OPTION 3
Idle mode & turbo mode
ENABLED
(AUTO)
/ turbo mode
ENABLED (MANUAL)
FEATURE 4 – Engine type and Cold Weather Mode
OPTION 1
Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)
OPTION 2*
Gas mode with 3-minute run time in cold weather mode
OPTION 3
Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)
OPTION 4
Diesel mode with 8-minute run time in cold weather mode (7-sec.wait to start delay)
