background image

2

WHAT’S INCLUDED

Please review the installation guide before
beginning the installation, particularly the
wiring diagram and the list of programming
options.

Prior to installation please be sure that all
hardware components required to install the
system are in the box.
The following is a list of components included
in the Kit:

 

1 – Control unit

 

2 – Transmitters (Depends on model)

 

Plug-in shock dual zone shock sensor

 

Plug-in ultra bright L.E.D

 

Plug-in valet switch

 

High power 120db, 6 tone siren

 

1 - 5 Pin 14 AWG harness (Ignition

harness)

 

1 - 7 Pin 18 AWG harness (Main harness)

 

1 - 11 Pin harness (Accessories)

 

1 Antenna (Link cable only with SH)

 

1 Parts Bag (hood switch, connector,

wires, warning label)

 

Installation Guide

 

User guide, tech bulletins.

NOTICE:

THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT.  SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.

INSTALLATION POINTS TO
REMEMBER

 

When working on a vehicle always leave a

window open.

 

Remove courtesy light fuse if possible to

prevent battery drain.

 

Never Install control unit where it could

interfere with normal operation or obstruct
service technicians.

 

Do not disconnect the battery on vehicles

equipped with air bags and anti-theft
radios.

 

Always use a grommet when running

wires into the engine compartment. Never
run wires through bare or sharp metal.

 

Always solder and tape all connections.

 

Never ground control unit to vehicle

steering column.

 

Make sure that vehicles OEM door switch

contacts and parking brake system works
properly.

FEATURES

 

programmable high current second
ignition / accessories / starter output

 

plug in valet and L.E.D

 

Smart-logic records last alarm state on
power up.

 

programmable factory horn / siren
output

 

5 zone protection

 

Smart-arm feature (system can arm
virtually any factory alarm!)

 

plug-in dual zone shock sensor

 

Ultra bright L.E.D.

 

Turbo Mode. (60 idle down)

 

external trigger control

 

pager ready

 

120db, small 6 tone siren

 

selectable passive or active starter kill
output

 

Silent arm/disarm capable by remote.

 

Siren panic mute, without disarming.

 

dedicated arm / disarm outputs

 

Auto zone 3 disarms with trunk release.

 

electronic ultra secure valet switch

 

diagnostics via parking light

 

12 volt parking light output

 

dual 12 volt supply

 

OEM alarm control

 

negative door lock outputs

 

ignition controlled door locks

 

anti-theft starter kill output

 

anti-grind feature

 

negative  trunk release output

 

child safety mode

 

code learning transmitter

 

user controlled cold weather timer

 

adjustable  tach search and setting

 

long range receiver (up to 1500 feet
range. sh model only)

 

programmable run time (5,15 or 25
minutes)

 

programmable crank attempts

 

programmable crank duration

 

2 YEAR LIMITED LIFE WARRANTY

OPTIONS

 

Remote keyless entry

 

Remote Trunk release

 

Engine kill (Starter kill)

 

OEM Horn control

 

Super-Heterodyne antenna

 

Multi-Car operation

 

Pager ready

Summary of Contents for AS-4560-SH












Reviews: