4
DISABLING ALARM VALET MODE
1.
Make sure the ignition key is in the OFF
position
2.
Set the alarm valet switch to ON
3.
Turn ignition ON
4.
Set the alarm valet switch to OFF. At this point
the
LED turns and stays OFF
to indicate that
the Alarm Valet Mode is disabled.
5.
Turn ignition OFF
ENABLING STARTER VALET MODE
1.
Make sure you did set the alarm valet
mode as you require.
2. Set the
valet switch ON
DISABLING STARTER VALET MODE
1.
Make sure you did set the alarm valet
mode as you require
2.
Set the
valet switch OFF
The remote starter is now in normal operation
TRANSMITTER FUNCTION
Once programmed, the transmitter will be
operational. (Hood must be closed)
The transmitter is depended on the module
type.
*The STOP Button on AS-4565 has NO
function.
NOTE:
Pressing any button with the vehicle
running, parking brake engaged and the doors
closed, will put the unit into Ready Mode.
TACH ADJUSTMENTS
Autostart systems have two methods of fine
tuning the tach signal that is generated from
the vehicle, the first method is manual tach
search and setting, and the second is
automatic tach search and setting. Either
method can be used, however an automatic
search is recommended.
Tach adjustment
procedures should be done every time a
new unit is installed.
This is because the
tach signal from some ignition systems can
sometimes be too high or too low, thus
causing failed starts under different
temperatures.
The procedures for tach adjustment are as
follows:
1. Hold hood switch down for 6 seconds
2. Release pinswitch (parking lights should
come on)
3. With parking lights on, immediately push
and release pinswitch again.
4. Parking lights will stay on for up to 20
seconds (if not repeat from step 1)
5. With lights on press Channel 3 (Trunk)
of remote transmitter at the same time.
(lights will flash 1 to 7 times)
6. Start the vehicle using the key.
7.
If lights stay on, then you have selected
an incorrect tach wire.
(relocate tach
wire and start from step 1)
If lights go
off then proceed to the next step.
8.
Allow vehicle to reach regular engine
idle speed, then press and release
brakes. (parking lights will flash
appropriate setting, from 1 to 7 flashes)
9.
Press Channel 3 (Trunk) of remote
transmitter, to save setting. (Parking
lights will flash one long flash)
NOTE: A manual adjustment should only
be done if the auto setting is not
completing the crank cycle properly in
cold weather.
MANUAL TACH SEARCH AND
SETTING
1. Hold hood switch down for 6 seconds
2. Release pinswitch (parking lights should
come on)
3. With parking lights on, immediately push
and release pinswitch again.
4. Parking lights will stay on for 20 sec. (if
not repeat from step 1)
5. Press Channel 3 (Trunk) of remote
transmitter at the same time (lights will
flash 1 to 7 times)
6. Now you can increase or decrease the
tach setting, depending on your needs.
7. Channel 1(LOCK) will decrease the
setting, and channel 2 (START) will
increase the setting.
8. After proper setting has been reached,
push Channel 3 (Trunk) to save setting.
(parking lights should flash once long)
CUSTOM PROGRAMMING OPTIONS
Autostart systems are equipped with 2
custom programming menus that allow the
user to custom fit the system according to
the installation requirements.
These options are designed to help make
interfacing with all vehicles possible.
To get into custom programming mode
you must do the following:
1. Hold pin-switch down for 6 sec.
2. Release pins-witch (parking lights will
come on)
3. Immediately push and release
pins-witch once again. (parking lights
will stay on for 20 sec.)
