5
4. Press and hold brakes, and press 1 or 2
on remote transmitter. (
Button 1 for
mode one, and Button 2 for mode two)
(lights will flash once for mode 1 and twice
for mode 2)
After you have entered into one of the two
programming menus you can release the
brake pedal. The unit will stay in programming
mode until the hood pins-witch is pressed or
the valet switch has been turned off. (
so take
your time to make the proper selection)
The menu will automatically start you at
function one, once you choose from one of the
three Options, you will automatically jump to
the next function.
To select one of the three options press the
appropriate transmitter button. (see below)
1. Channel 1 (LOCK) = Option 1
2. Channel 2 (START) = Option 2
3. Channel 3 (TRUNK) = Option 3
Once an option has been selected the parking
lights will flash 1,2 or 3 times. (
Depending on
option selected)
CUSTOM OPTIONS
MODE 1 PROGRAMMING
Function 1: Ignition Lock, Door lock/unlock
Toggled, Dual Lock Pulses
•
Channel I*
Ignition Lock Enabled
•
Channel II
Ignition Lock Disabled
•
Channel III
Ignition Lock Disabled
&SecureLock enabled
Note:
Secure lock
adds a lock pulse 4
seconds after the module starts the engine
and also 4 seconds after it stops the engine.
Function 2: Must Select default setting.
•
Channel I*
Enabled
•
Channel II
Enabled
Function 3: Arming/disarming Chirp
•
Channel I*
Chirp Enabled
•
Channel II
Chirp Disabled
Function 4: Passive/Active Arming
•
Channel I*
Passive Arming
•
Channel II
Active Arming
Function 5: Door Lock Pulse Time
•
Channel I*
¾second Lock/Unlock
pulse
•
Channel II
4 second
Lock/Unlock pulses
•
Channel III
3/4second Lock pulse,
and two 1/4second
Unlock
pulses.
Function 6: Siren / OEM Horn Mode
•
Channel I*
SirenMode Enabled
•
Channel II
SirenMode Enabled
•
Channel III OEM Horn Mode
* = Factory Default
This conclude Mode 1 programming. To get a
playback of these options, press and release the
hood switch. The programming of these four
functions (and those from Mode 2) will play back
in sequence via the parking lights.
CUSTOM ENGINE OPTIONS
MODE 2
This mode allows you to customize the
alarm/remote starter's control of crank
cycles, engine run time and diesel engine
options.
Function 1: Engine Run Time
•
Channel I
5 minutes
•
Channel II*
15 minutes
•
Channel III
25 minutes
Function 2: Crank Cycles
•
Channel I
2 max.
•
Channel II*
3 max.
•
Channel III
4 max.
Function 3: Crank Time
•
Channel I
6 seconds max.
•
Channel II*
8 seconds max.
•
Channel III
12 seconds max.
Function 4: Not Used
•
Channel II*
Disabled
Function 5: Engine Type
•
Channel I
Gasoline Engine
•
Channel II*
Gasoline Engine
•
Channel III
Diesel Engine
* = Factory Default
This conclude Mode 2 programming. See
Mode 1 for playback options.
TACH WATCH LOCKOUT
Tach Watch lockout is a safety feature built
into the remote starter to protect the
vehicle’s starter motor. If, during remote
start, the vehicle’s engine ever cranks the
entire programmed crank time without
detecting any tach pulses during the first
crank cycle, the unit will go into tach watch
lockout. The diagnostics for this is 3 quick
parking light flashes when trying to remote
start the vehicle.
If your module is in Tach Watch Lockout it is
indicating that a problem exists with the tach
signal it is receiving. Verify that the tach
wire from the remote starter is properly
connected to a good tach signal in the
vehicle.
To remove the unit from Tach Watch
Lockout you must do the following:
