MODE 1
( * indicates default setting)
FUNCTION 1 – Ignition-controlled Door Locks
OPTION 1*
Ignition-controlled Door Locks
ENABLED
OPTION 2
Ignition-controlled Door Locks
DISABLED
FUNCTION 2 – Secure Lock
OPTION 1*
Secure Lock
DISABLED
OPTION 2
Secure Lock
ENABLE
FUNCTION 3 – Passive / Active Arming of the Starter Kill
OPTION 1*
Starter Kill
PASSIVE
(1-minute timeout.)
OPTION 2
Starter Kill
ACTIVE
OPTION 3
Starter Kill
PASSIVE
(3-minute timeout.)
FUNCTION 4 – Lock Pulse Duration
OPTION 1*
7/10-second
LOCK / UNLOCK
pulses
OPTION 2
4-second
LOCK / UNLOCK
pulses
OPTION 3
7/10-second
LOCK
pulse and
two
1/4-second
UNLOCK
pulses
MODE 2
( * indicates default setting)
FUNCTION 1 – Engine Run Time
OPTION 1
4-minute Run Time in Gas Mode / 9-minute in Diesel Mode.
OPTION 2*
15-minute Run Time in Gas Mode / 20-minute in Diesel Mode.
OPTION 3
25-minute Run Time in Gas Mode / 30-minute in Diesel Mode.
FUNCTION 2 – Idle Mode
OPTION 1
Idle Mode
DISABLED
OPTION 2*
Idle Mode
ENABLED
OPTION 3
Idle Mode
DISABLED
FUNCTION 3 – Engine Type – Gas or Diesel
OPTION 1
DIESEL
Engine Mode
OPTION 2*
GASOLINE
Engine Mode
OPTION 3
DIESEL
Engine Mode
Installation-programmable Features
The following features can be programmed according to the user’s needs and the requirements of the installation.
Ignition-controlled Door Locks
(Mode 1, Function 1: Option 1 –
ON
– by default.)
This feature will automatically lock all Doors as soon as the key is
turned to the
IGNITION ON (RUN)
position, and the Brake Pedal is pressed. When the Ignition Key is turned to the
OFF
position, the Doors will automatically be unlocked.
Secure Lock
(Mode 1, Function 2 , Option 1 –
OFF
by default.)
This feature allows the Module to control certain OEM factory Alarm
systems that use the factory Lock wire to
arm
the Alarm and the Unlock wire to
disarm
it.
If Secure Lock is disabled (Option 1), the Module will still disarm before remote-starting the vehicle. If Secure Lock is
enabled (Option 2), upon receiving a remote
START
signal the Module will
UNLOCK
the Doors (disarming the factory
Alarm); 1/2 sec. after remote start it will
re-lock
the Doors. 4 seconds after shutdown, Secure Lock will
re-lock
all
Doors once more (
arming
the system again).
Please note
that most OEM systems will
not
rearm the Alarm while the
Engine is running, but
will
lock the Doors.
Passive or Active Arming of the Starter Kill
(Mode 1, Function 3: Option 1 – Passive with a 1-min. timeout – by default.)
The Starter Kill can be programmed
to be
active
(
will not
arm automatically) or
passive
(
will
arm automatically). In Passive Mode, you can program it to
arm automatically in 1 or 3 min.
To
disarm
the Starter Kill in Active or Passive Mode, the user must press and hold the
UNLOCK
button on the
Transmitter (or enable Valet Mode). The Parking Lights will flash twice. If the Door Locks option was installed, this will
also unlock the Doors.
To
arm
the Starter Kill in Active or Passive Mode, the user must press and hold the
LOCK
button on the Transmitter.
The Parking Lights will flash once. (If the Door Locks option was installed, this will also lock the Doors). In Passive
Mode, the system will automatically arm itself 1 or 3 minutes after the Engine is shut down.
PS-2925
Installation Guide
P. 9
