Page 20
Instruction manual 50170101
Version 1 April-08
Please follow the processes of use of this manual.
This manual should be available for all users of this equipment.
Always use original components and supplies. Other devices can be similar but they
can damage the equipment.
The microscope is supplied with a standard wire and it should be connected to a current
wire provided with an earth wire, it should be handy to be disconnected in case of emer-
gency.
Never try to repair the microscope by yourself, since you will lose the warranty and
may provoke damages to the general operating system or the electrical installation, as
well as injuries to the people that usually handle the microscope (burns, hurts…) or dama-
ges in nearby equipments.
In the event of breakdown please contact your distributor to overhaul through Zuzi
Technical Assistance Department.
Changing the lamp
IMPORTANT: before changing the lamp bulb or the fuse, make sure that the
microscope is disconnected from the net. Check you are using the proper
lamps, as other types can provoke malfunction.
Turn off and unplug the microscope.
Remove the lid of the lamp compartment
(4.8).
Take the lamp and pull firmly to remove it. If the lamp is hot, take care and do not touch
the lamp to avoid burns.
Replace the lamp for another one, making sure it is a 20 W Zuzi original one. Please take
care and do not touch the lamp with bare hands. Do not use lamps with a higher power,
as they could provoke over heating or any malfunction.
Put again the lamp compartment lid
(4.8)
.
If necessary, center again the lamp as previously indicated.
Cleaning
NOTE: Zuzi recommends using the microscope cleaner kit (code 89000001).
Never use scourers or substances that can grate for cleaning metallic parts such as stain-
less steel, aluminium, coatings, etc. as they damage the microscope and produce an early
ageing of the equipment.
Use a fluff-free cloth dampened with soaped water that does not contain abrasives.
Lenses must not be disassembled by the user. Were there any dust or dirt to be cleaned,
clean it with a natural horse hair brush or a smooth piece of cloth, fluff-free, dampened
with a bit of xylene or toluene.
To remove dust from lenses, blow them with a plastic bulb or clean them with a natu-
ral horsehair brush.
Use non-corrosive lubricants in metallic parts, being careful of not touching optical
Version 1 April-08
Instruction manual 50170101
Page 13
ATTENTION!! IF EQUIPMENTS ARE NOT PROPERLY CLEAN AND DISINFEC-
TED THEY WOULD NOT BE ALLOWED TO REPAIR BY OUR TECHNICAL SERVICE.
INDEX OF LANGUAGES
Spanish
English
French
2-11
12-21
22-32
1. USES OF THE INSTRUMENT
2. DESCRIPTION
3. TECHNICAL SPECIFICATIONS
4. INSTALLATION / SETTING UP
5. MAINTENANCE AND CLEANING
ANNEX I: CE CERTIFICATE
13
13
14
15
19
32
INDEX OF CONTENTS
1. USES OF THE INSTRUMENT
Zuzi metallurgical microscope model 101 is aimed to the microscopic study of any kina
of opaque samples covering a wide range of applications in industry and research. It has
been especially designed to require a minimum optical and mechanical maintenance assu-
ring years of high quality and reliable service.
2. DESCRIPCIÓN
1.1 Filter holder
1.2 Field diaphragm centering screw
1.3 Polarizer adjustment lever
1.4 Trinocular tube
1.5 Sliding rod to direct light
1.6 Analyzer
1.7 Objectives
1.8 Stage
1.9 Upper focus limit control
1.10 Coarse adjustment knob
1.11 Fine adjustment knob
1.12 Stage quick adjustment knob
1.13 Eyepieces
1.14 Binocular head holding screw
1.15 Field diaphragm adjustment lever
1.16 Aperture diaphragm adjustment
lever
1.17 Socket
1.18 Light intensity control
1.19 On/off switch
1.20 Stage cross movement knob
1.21 Stage longitudinal movement knob
1.22 Friction control ring
ENGLISH
ENGLISH