background image

AW58EMVAP  |  AW584EMVSU

User’s Manual

PAGE 2

Technical Support

 (650) 384-0000

www.avalan.com

© by AvaLAN Wireless Systems Inc. All rights reserved.

Revision 05.10.2018

127 Jetplex Circle 

Suite A

Madison, AL 35758

Phone: (650) 384-0000

Fax: (650) 249-3591

READ THIS MANUAL BEFORE YOU BEGIN

Dispensers have both electricity and a hazardous, flammable and potentially explosive liquid. Failure 

to follow the below precautions and the Warning and Caution instructions in this manual may result 

in serious injury. Follow all rules, codes and laws that apply to your area and installation.

SAFETY PRECAUTIONS - INSTALLATION AND MAINTENANCE

Always make sure ALL power to the dispenser is turned OFF before you open the dispenser cabinet 

for maintenance. Physically lock, restrict access to, or tag the circuit breakers you turn off when 

servicing the dispenser. Be sure to trip (close) the emergency valve(s) under the dispenser BEFORE 

beginning maintenance.

Make sure that you know how to turn OFF power to the dispenser and submersible pumps in an 

emergency. Have all leaks or defects repaired immediately.

HOW TO CONTACT AVALAN WIRELESS

Problems with the installation of this kit should be referred to AvaLAN Technical Support:

(650)384-0000.

INDICATORS AND NOTATIONS

   

Danger indicates a hazard or unsafe practice which, if not avoided, will result in severe injury 

or possibly death.

Warning indicates a hazard or unsafe practice which, if not avoided, may result in severe 

injury or possibly death.

Caution indicates a hazard or unsafe practice which, if not avoided, may result in minor injury.

NOTE:

 Important information to consider, otherwise, improper installation and/or damage to

components may occur.

Summary of Contents for AW584EMVSU














Reviews: