background image

 

 

 
 

INSTALLING THE SHELVES: 

1.

 

Open the door completely. 

2.

 

Ensure that the plastic posts are installed on the left and right sides of the shelf track onto which you are 
attempting to install the shelf.  

3.

 

Lifting the rear of the shelf upwards above the shelf track, align the cutouts in the left and right sides of 
the shelves over the plastic posts mounted to the inner cabinet. 

4.

 

Gently set the shelf down on the shelf track.  

REMOVING THE SHELVES: 

1.

 

Open the door completely. 

2.

 

Make sure the shelf is pushed back completely. 

3.

 

Lift either the left or right side of the shelf to create a 45° angle from its original position.  Make sure not 
to lift either side of the shelf too hard as it may come in contact with the inner wall mount.   

4.

 

Pull the shelf outward until it is removed from the inner compartment.  You may encounter some 
resistance from the shelf guard rail.   

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

Tip: To prevent damaging the door gasket, make sure to open the door fully before pulling the shelves out 
of their track. 

Summary of Contents for AFR151SSLH



















Reviews: