AVANT 700 2012 Series Operator'S Manual Download

Page: 15 / 36

700 Series

Attachment control

switch pack (option)

Optional extra with which

electric functions of the

attachment are controlled

Does not require the

optional 8 function joystick

on the loader.

Consists of socket that

mounts on the boom. The

electric harness of the

attachment is connected

to this socket, and the

electric features are

controlled with switches

mounted on the boom

control lever.

Read the operators

manual of the attachment

to see how the switches

are used with each

attachment.

Control of loader boom, auxiliary hydraulics and other functions

Most of the functions of the loader are controlled at the control panel on the right side of the operator: Boom

and bucket movements, auxiliary hydraulics (attachments), engine revs etc. , depending on loader model.

Following pictures show the different functions:

5. Control lever of boom and bucket

(Functions of the optional electric joystick are explained on page 18)

Pull backward to lift the boom

Push forward to lower the boom

Push left to raise the tip of the bucket (filling)

Push right to lower the tip of the bucket (emptying)

6. Hand throttle lever

Push forward to increase engine revs

Pull backward to reduce engine revs

7. Control lever of auxiliary hydraulics

(hydraulically operated attachments)

Push forward: Hydraulic flow to pressure 1

coupler. Move the lever carefully to see which

way the hydraulic attachment moves.

Pull backward: the attachment moves in opposite

direction

Locking position: Continuous flow to pressure

1 coupler.

8. Control lever of telescopic boom

(optional extra)

Push forward to extend the boom

Pull backward to retract the boom

9. Control lever of extra auxiliary hydraulics

outlet (optional extra)

The control lever operates either the rear

hydraulics outlet or the extra front outlet.

Push f locking position: Move the lever

carefully to see which way the hydraulic

attachment moves.

Pull backward: the attachment moves in opposite

direction

10.Selection lever of the pumps for auxiliary

hydraulics

Lever in front position (1-pump): one pump

coupled for auxiliary hydraulics

Lever in back position (1-pump): both pumps

coupled for auxiliary hydraulics

Operating instructions

https://tractormanualz.com

Summary of Contents for 700 2012 Series





































Search results

Summary of Contents for 700 2012 Series

Reviews:

Related manuals for 700 2012 Series

Brands by name

Popular brands

AVANT 700 2012 Series, Operator'S Manual

Search results

Summary of Contents for 700 2012 Series

Reviews:

Related manuals for 700 2012 Series

Brands by name

Popular brands