manualshive.com logo in svg

AVANT 700 2012 Series, Operator'S Manual

The AVANT 700 2012 Series Operator's Manual is a comprehensive guide that empowers users with in-depth knowledge on operating and maintaining their AVANT 700 machine. This manual is available for free download at 88.208.23.73:8080, ensuring easy access to essential instructions and valuable insights for optimal product performance.

Share
Download
background image

700 Series

Operating instructions

25

Make sure that the attachment is properly connected on the

attachment coupling plate. An attachment that comes loose may

tip over or fall on the loader, causing personal injuries.

Do not try to lock the locking pins by using the brackets on the

boom when the attachment is lifted over one metre from the

ground. Lock the locking pins by hand and make sure that both

pins lock properly down in the holes of the attachment.

Always read also the additional instructions for coupling and using

of the attachment in the Operators Manual of the attachment.

Coupling  the hydraulic hoses of the attachment

Hydraulic hoses of the attachment are equipped either with the multi connector or with conventional type

quick couplers. Contact your Avant dealer if you wish to change the coupler type.

Coupling the multi connector

Align the pins of the attachment connector with correspondig

holes of the loader connector. Connecting is not possible if the

multi connector for some reason is mounted in a wrong way on

the attachment hoses. Connect and lock the multiconnector by

turning the lever towards the loader.

The lever should move easily all the way to locking poisition. If

the lever doesn’t move easily, check alignment and position of the

attachment and loader side connectors and clean the connectors.

Stop the engine and release pressure in auxiliary hydraulics line

by moving the auxiliary hydraulics control lever in both directions

a couple of times.

Disconnecting the multi connector

• Before disconnecting put the attachment down on a solid and

even surface. Switch off auxiliary hydraulics. Disconnect

attachment hoses by pressing on the red button on the

multiconnector and simultaneously turn the lever away from

the machine.

• After ending operation put the multi connector on its "parking"

on the attachment.

Conventional type quick couplers

• Engine must be stopped when connecting the hoses. Before

connecting the hoses move the auxiliary hydraulics control lever

in both directions a couple of times in order to release eventual

back pressure.

NOTICE! When fitting an attachment, make sure

that the hydraulic hoses are not overstretched and

are not in a position where they can be trapped

during the operation of the machine and

attachment.

https://tractormanualz.com

Summary of Contents for 700 2012 Series





































Reviews:

No comments

Related manuals for 700 2012 Series

Brands by name

Popular brands

Load more brands