background image

Introduction, warranty

700 Series

3

Introduction

AVA

NT

 TECNO OY wants to thank you for purchasing this AVANT loader. It is the result of Avant’s long

experience in design and manufacturing of compact loaders.

We ask you that you read and understand the contects of this manual completely before operating the loader.

This will improve your operating and maintenance efficiency, help avoid breakdowns and damage and extend

your machine’s life.

Contact your local AVANT dealer for any questions, service, spare parts or about any problems that may occur

with the operation of your machine.

Keep this Operators Manual with the machine at all times.  If this Manual gets lost, ask for a new copy from

your Avant dealer. Remember also to give this Manual to the new owner when the machine changes ownership.

AVANT 745/750 WARRANTY

This warranty specifically applies to the AVANT 745/750 loader only and not to any attachments used with

this product.

Any repairs or modifications performed without the prior authorisation of Avant Tecno Oy will cancel this

warranty.

During the first year of operation or first 750 hours (whichever is the soonest) Avant Tecno Oy warrants to

replace any part or repair any defect which may occur, subject to the terms detailed below:

1) The product has received regular maintenance in accordance with schedules given by the manufacturer.

2) Any damage caused by operation in a negligent manner or exceeding the approved specifications detailed

in this manual is excluded.

3) Avant Tecno Oy accepts no responsibility for interruption to working or any other consequential losses

resulting from any failure of the product.

4) Only Avant Tecno Oy approved replacement or original quality parts shall be used during routine maintenance.

5) Any damage caused by the use of incorrect fuel, lubricants, cooling liquid or cleaning solvents is excluded.

6) The Avant Warranty excludes any consumable parts (e.g. tyres, batteries, filters, belts etc.) except where

it can be clearly shown that these parts were defective on original supply.

7) Any damage caused resulting from the use of attachments not approved for use with this product is excluded.

8) In the event a fault occurs which is attributable to manufacturing or assembly defect you should arrange

to return your AVANT to your authorised dealer for repair. Travel and freight costs are excluded.

Intended use

AVANT 745/750 is an articulated compact loader, designed and manufactured for both professional and private

use. The loader can be equipped with attachments offered by Avant Tecno Oy, which enables doing of several

different jobs.  Because of this multi purpose nature of the machine and the various attachments and tasks,

read always not only this Manual but also the Operators Manual of the attachment, and follow all instructions.

Every person who has to do with this machine must follow work safety regulations, all other generally accepted

rules related to work health and safety, and all road traffic regulations.

Remember that safety consists of several factors. The loader, equipped with an attachment is very powerful

and can cause serious personal injuries or property damages if it is operated in a wrong or careless way. Do

not operate an attachment unless you have familiarised yourself with the use of it and the eventual dangers

related to it.

These operating instructions are intended to help to:

• operate this machine safely and efficiently

• observe and prevent situations that may cause a risk or danger

• keep the machine in good condition and its life span as long as possible

This loader has been designed to require as little maintenance as possible. The operator can perform the most

common maintenance operations. There are however more demanding service operations that can be done

by professional service personnel only. It is allowed to perform service operations only when wearing appropriate

protective equipment. Original spare parts must be used. Familiarise yourself with the service and maintenance

instructions in this Manual.

Contact your local AVANT dealer, if you are uncertain of anything concerning the operation and maintenance

of this loader, or for any questions, service or spare parts.

https://tractormanualz.com

Summary of Contents for 700 2012 Series





































Reviews:

Related manuals for 700 2012 Series