background image

6 (26) 

 

 

 

 

2.

 

Designed purpose of use 

This AVANT Weed brush is an attachment that is suitable for use with AVANT multi purpose loaders that are 

shown in Table 1. The Weed brush is an efficient tool for removal of weeds on all kinds of paved areas. The 

manually adjustable, telescoping arm of the rotating brush makes it easy to remove unwanted weed from 

pathways and around cornerstones, and allows working near buildings. The weed brush is equipped with a 

support wheel as standard, which can be lifted and locked up to transport position if needed. 
The weed brush is equipped with a steel brush which can be extended manually and turned in three different 

positions: to the front, to the right side, or to the left side. The brush arm should be set to front position for 

storage of the attachment. The weed brush is intended only for maintenance of level ground surfaces. Other 

tools than the brush must not be installed on the attachment. The Weed brush is not designed for any other 

use than what is specified in this manual and must not be used for any other purposes than what is intended 

for. 

 

The attachment has been designed to require as little maintenance as possible. The operator can perform 

regular maintenance tasks. All repair work can’t be performed by the operator, and demanding repair and 

maintenance operations are to be left for professional maintenance. All maintenance work must be done using 

proper safety equipment. Spare parts must be identical with original specifications, which can be ensured by 

using only original spare parts. A separate spare parts catalogue may be available, consult your Avant dealer. 
Familiarise yourself with the manual's instructions regarding service and maintenance. Please contact your 

AVANT retailer if you have additional questions about the operation or maintenance of the equipment, or if 

you require spare parts or maintenance services. 

 

Table 1 - Weed brush - Compatibility with Avant loaders 

Avant 

220

 series 2

 

225 

225LPG 

313S 
320S 

420 
423 
520 
523 

R20 

525LPG 

R28 

528 
530 

630 

R35 

635 
640 

745 
750 

755i 
760i 

850 

860i 

e5 
e6 

A36594 

 

 

 

 

 

 

 

 

 

Summary of Contents for A36594



























Reviews: