manualshive.com logo in svg

Avaya Application Solutions, Deployment Manual

Avaya Application Solutions offers a comprehensive range of user manuals, including the highly sought-after Deployment Manual. Easily accessible for download at no cost, these manuals provide step-by-step guidance and expert insights. Enhance your product knowledge and maximize its potential with our free user manuals, available at 88.208.23.73:8080.

Share
Download
background image

Midspan Power Unit

Issue 3.4.1 June 2005

119

 

Power priority mechanism

The priority mechanism is implemented in order to handle cases where the power requested by 
the PDs exceeds the switch PoE capacity. This priority mechanism determines the order in 
which ports will be powered on after boot, and powered off if the power resources of the module 
are exhausted. Three user-configurable port power priority levels are available: low, high & 
critical. Within each priority level the lower the port number, the higher the priority (by default all 
the ports have low priority).

Disconnected power will be automatically reconnected to the PDs based on their priority, 
whenever there is an available power budget. Immediately after the PoE has booted up, it starts 
to supply power to the ports where a load is detected. Ports are powered up one after another, 
based on the port priority, until the limit is reached. Power calculation is based on the actual 
power consumption of the PD. After this, no more ports are powered up until the total power 
consumption drops lower than the limit. The limit is 18 Watts below the maximum PoE capacity. 
The remaining 18W are reserve power for a change in the power draw of PDs.

Midspan Power Unit

Description

The official name for this device is the 1152A1 Power Unit, but the Midspan Power Unit can also 
be called a powered data unit (PDU) or a power over Ethernet (POE) device. The Midspan 
Power Unit is 1U in height (1.75 inches or 4.44 cm) and has 24 RJ45 data input jacks on the 
bottom row, and 24 data and power output RJ45 jacks. Data flow is unaffected if power is 
disrupted and if the endpoint does not require power. An example is a laptop computer that is 
connected to the 1152A1. The computer does not receive power from the 1152A1. If the 
120-volt power is disrupted to the 1152A1, the computer data stream would not be affected. The 
1152A1 unit provides a maximum of 200 watts or a peak of 16.8 watts per port. This unit powers 
any device that conforms to the 25-K Ohm resistive signature defined in the IEEE 802.3-2003 af 
standard. This unit also powers devices that use the nonstandard capacitive signature, such as 
Cisco IP telephones. The 1152A1 provides positive voltage on pins 4/5 and negative voltage on 
pins 7/8, which is one of the three methods as described by the IEEE 802.3af standard.

Designed usage

The Midspan Power Unit is designed to mount in a 19-inch data rack, or can be stacked up to 
four units high using the optional rubber feet. Its niche is to provide power to only those IP 
endpoints that need power. The alternative is to have a switch that incorporates power. 
However, any nonpowered device that uses that switch is not using the power capabilities of the 
switch, and does not justify the higher price per port of that switch. The Midspan Power Unit 
solves this problem by providing power without altering the network topology.

Summary of Contents for Application Solutions





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Application Solutions

Neoi 136 User Manual preview
136
Brand: Neoi Pages: 50
E-Boda Sunny V38 Quick Start Manual preview
Sunny V38
Brand: E-Boda Pages: 50
Caliber HFB 400 User Manual preview
HFB 400
Brand: Caliber Pages: 10
i.safe MOBILE M655A01 Quick Start Manual preview
M655A01
Brand: i.safe MOBILE Pages: 72
AU Xperia ZL2 Sol25 Settings Manual preview
Xperia ZL2 Sol25
Brand: AU Pages: 2
T-Mobile MDA Get Started preview
MDA
Brand: T-Mobile Pages: 2
Alcatel One Touch 903 Smart Quick Start Manual preview
One Touch 903 Smart
Brand: Alcatel Pages: 21
Samsung SGH T319 Manual Del Usuario preview
SGH T319
Brand: Samsung Pages: 182
Samsung SGHP735 User Manual preview
SGHP735
Brand: Samsung Pages: 193
Samsung SGH T349 Information Manual preview
SGH T349
Brand: Samsung Pages: 2
Samsung SM-A025U-UM User Manual preview
SM-A025U-UM
Brand: Samsung Pages: 120
Zte Prelude Quick Start Manual preview
Prelude
Brand: Zte Pages: 24
Xiaomi Redmi 3 User Manual preview
Redmi 3
Brand: Xiaomi Pages: 2
BRONDI AMICO SMART Instruction Manual preview
AMICO SMART
Brand: BRONDI Pages: 15
Avaya 2007 User Manual preview
2007
Brand: Avaya Pages: 182
Haier Muzik V70 User Manual preview
Muzik V70
Brand: Haier Pages: 32
Avvio 766 User Manual preview
766
Brand: Avvio Pages: 46
avus A 57 Instruction Manual preview
A 57
Brand: avus Pages: 70

Brands by name

Popular brands

Load more brands