manualshive.com logo in svg

Avaya Application Solutions, Deployment Manual

Avaya Application Solutions offers a comprehensive range of user manuals, including the highly sought-after Deployment Manual. Easily accessible for download at no cost, these manuals provide step-by-step guidance and expert insights. Enhance your product knowledge and maximize its potential with our free user manuals, available at 88.208.23.73:8080.

Share
Download
background image

Traffic engineering

182 Avaya Application Solutions IP Telephony Deployment Guide

 

 Example 7: LAN bandwidth

In 

Example 6: IP bandwidth considerations

, the total IP LAN bandwidth usage for each site was 

calculated, and expressed in Erlangs at the bottom of 

Table 34: IP LAN bandwidth usages 

(Erlangs) for Example 6: IP bandwidth considerations

on page 179. Specifically, the total LAN 

bandwidth usage in Site 1 is 123.5 Erlangs, in Site 2 is 56.6 Erlangs, and in Site 3 is 29.2 
Erlangs. This implies that the average number of bidirectional media streams that are 
simultaneously in use at any given time in Site 1 is 123.5. Analogous statements can also be 
made regarding Sites 2 and 3.

Every media stream across the IP LAN in any of the three sites is assumed to use the 
uncompressed G.711 codec, since bandwidth is relatively inexpensive within a private LAN, as 
opposed to a public WAN. Assume, for the sake of this example, a standard IP packet size of 20 
ms. So for the G.711 codec, 

Table 37: Bandwidth requirements for media streams

on page 181 

indicates that each media stream consumes 87.2 kbps of IP LAN bandwidth. It may be tempting 
at this point to simply multiply 87.2 kbps by 123.5 simultaneous bidirectional media streams, to 
arrive at the estimate for the overall LAN bandwidth needed for Site 1. However, 123.5 is merely 
the average number of simultaneous media streams, and approximately half of the time, there 
are at least 124 simultaneous media streams in use.

In this example, suppose that the goal is to supply enough bandwidth to adequately support the 
media streams at least 99.9% of the time. The standard infinite-server queueing model implies 
that less than 0.1% of the time there are at least 159 simultaneous media streams in the Site 1 
LAN. So, it is sufficient to engineer the LAN bandwidth to support 158 simultaneous media 
streams. Therefore, the Site 1 LAN requires at least (158 simultaneous media streams) x (87.2 
kbps per media stream) = 13.8 Mbps of bandwidth, in each direction. This result, along with the 
analogous results for Sites 2 and 3, are provided in 

Table 38: IP LAN bandwidth requirements 

in each direction, for Example 7: LAN bandwidth

.

In 

Table 38

, the number of simultaneous media streams for “P001” represents the 99.9th 

percentile for the number of simultaneous unidirectional streams, as determined by applying the 
standard infinite-server queueing model.

A slight variation of the procedure that was used to determine LAN bandwidth in 

Example 7: 

LAN bandwidth

 can be used to determine WAN bandwidth. Using compressed RTP (cRTP) is a 

means to conserve bandwidth. Specifically, the use of cRTP reduces the overhead due to IP, 
UDP, and RTP from 40 bytes to between 2 and 4 bytes (4 bytes are assumed for this example). 
Using the PPP overhead of 7 bytes (which would vary if ATM, HDLC, or Frame Relay were 

Table 38: IP LAN bandwidth requirements in each direction, for 

Example 7: LAN 

bandwidth

Resource

Site 1

(Atlanta)

Site 2

(Boston)

Site 3

(Cleveland)

Simultaneous media streams for 
“P001”

158

81

47

LAN bandwidth (Mbps)

13.8

7.1

4.1

Summary of Contents for Application Solutions





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Application Solutions

Samsung SM-A356E User Manual preview
SM-A356E
Brand: Samsung Pages: 155
Iget blackview Crown Quick Start Manual preview
blackview Crown
Brand: Iget Pages: 76
WM Systems M2M Easy2s Installation Manual preview
M2M Easy2s
Brand: WM Systems Pages: 102
Cricket Icon 2 Quick Start Manual preview
Icon 2
Brand: Cricket Pages: 12
Watchguard WGSMSB User Manual preview
WGSMSB
Brand: Watchguard Pages: 12
Profoon PM-778 User Manual preview
PM-778
Brand: Profoon Pages: 56
INQ iNQ1 User Manual preview
iNQ1
Brand: INQ Pages: 101
HTC ROSE100 User Manual preview
ROSE100
Brand: HTC Pages: 226
InFocus IN610 User Manual preview
IN610
Brand: InFocus Pages: 120
UTStarcom GSM708 User Manual preview
GSM708
Brand: UTStarcom Pages: 54
Alcatel IDOL4 Manual preview
IDOL4
Brand: Alcatel Pages: 121
HTC PURE AT&T Safety And Regulatory Information Manual preview
PURE AT&T
Brand: HTC Pages: 16
M4TEL M4 B3 Quick Start Manual preview
M4 B3
Brand: M4TEL Pages: 13
AKUA EK4e User Manual preview
EK4e
Brand: AKUA Pages: 34
Flyingvoice FIP12WP User Manual preview
FIP12WP
Brand: Flyingvoice Pages: 51
Intelbras TIP 200 LITE Installation Manual preview
TIP 200 LITE
Brand: Intelbras Pages: 52
Spice C-5300 Manual preview
C-5300
Brand: Spice Pages: 21
Zte F165 User Manual preview
F165
Brand: Zte Pages: 89

Brands by name

Popular brands

Load more brands