manualshive.com logo in svg

Avaya Application Solutions, Deployment Manual

Avaya Application Solutions offers a comprehensive range of user manuals, including the highly sought-after Deployment Manual. Easily accessible for download at no cost, these manuals provide step-by-step guidance and expert insights. Enhance your product knowledge and maximize its potential with our free user manuals, available at 88.208.23.73:8080.

Share
Download
background image

Avaya Application Solutions platforms

42 Avaya Application Solutions IP Telephony Deployment Guide

 

The G350’s internal router enables you to connect directly to an outside WAN, without needing 
additional routing equipment.

The G350 provides telephone services through an Avaya media server, such as the S8300. The 
media server controls the routing of voice traffic through the G350. The media server can be 
either internal (S8300) or external (S8700, S8500, or S8300). The media server runs Avaya 
Communication Manager software.

Pluggable media modules provide interfaces for many types of telephones and trunks. This 
allows you to incorporate legacy end point devices such as analog and digital telephones.

The G350 can be managed through the Avaya G350 Command Line Interface, the G350 
Device Manager graphic user interface, or the centralized Avaya Integrated Management 
application.

G350 Configurations

The G350 is a modular device with multiple configuration possibilities to meet specific individual 
needs. Six slots in the G350 chassis house various media modules, providing connections for 
different telephones, telephone trunks, data devices, and data lines.

 Media server configuration options for the G350 include:

●

Standalone. In this configuration, one media module slot houses the S8300 internal Media 
Server, which runs the call control applications for the G350. The remaining slots house a 
customized selection of media modules, which connect to circuit-switched phones, trunks, 
and data devices. This configuration is capable of supporting up to 40 stations (maximum 
of 26 legacy Analog/DCP stations) and 35 trunks, including both circuit-switched and 
IP-switched endpoints. 

●

Media Gateway. In this configuration, there is no internal media server. The G350 is 
dependent on a separate controller. This may be an external standalone media server 
such as the S8500 or S8700 or the S8300 housed in a separate media gateway. All six 
media module slots are available to house a customized selection of media modules.

●

Survivable. In this configuration, an external media server provides primary controlling 
service to the G350. The S8300 populates one of the module slots as a backup controller 
and functions in Local Survivable Processor (LSP) mode. If the external media server 
stops serving the G350, the S8300 takes over the service. As for standalone configuration, 
the remaining slots house a customized selection of media modules.

Each G350 should deploy as a single unit at a remote location. Multiple G350s may be 
deployed in many remote branches of a large organization. Large branches or main offices 
requiring more capacity than a single G350 should deploy one or more Avaya G700 Media 
Gateways. In addition to media gateway functions similar to those of G700, the G350 can 
optionally provide integrated power-over-Ethernet and WAN routing functions through media 
modules.

The G350 now supports up to 10 concurrent call center agents. Customers requiring more call 
center agents in a small branch office should consider the G700 media gateway.

Summary of Contents for Application Solutions





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Application Solutions

Tyco 3G4010 v4.0 Installation Manual preview
3G4010 v4.0
Brand: Tyco Pages: 36
Talkswitch TS-550i User Manual preview
TS-550i
Brand: Talkswitch Pages: 83
Oval EL 2310-08E Series Instruction Manual preview
EL 2310-08E Series
Brand: Oval Pages: 80
Wafer Microelectronics GSM-HELP Quick User Manual preview
GSM-HELP
Brand: Wafer Microelectronics Pages: 6
Infinix X6817 User Manual preview
X6817
Brand: Infinix Pages: 11
Grandstream Networks GXV3350 Quick Installation Manual preview
GXV3350
Brand: Grandstream Networks Pages: 10
NEG F1020 User Manual preview
F1020
Brand: NEG Pages: 10
Maxcom MM821 Manual preview
MM821
Brand: Maxcom Pages: 46
ICON IP2032 Quick Reference Manual preview
IP2032
Brand: ICON Pages: 8
Lemon iQ 303 User Manual preview
iQ 303
Brand: Lemon Pages: 33
OUKITEL WP18 Quick Start Manual preview
WP18
Brand: OUKITEL Pages: 60
switel M 180 Quick Start Manual preview
M 180
Brand: switel Pages: 4
AEG Voxtel M320 User Manual preview
Voxtel M320
Brand: AEG Pages: 224
Philips X818 Manual preview
X818
Brand: Philips Pages: 28
Zte nubia 5 User Manual preview
nubia 5
Brand: Zte Pages: 24
Samsung Galaxy A51 Quick Start Manual preview
Galaxy A51
Brand: Samsung Pages: 2
Samsung Galaxy A10e Quick Reference Manual preview
Galaxy A10e
Brand: Samsung Pages: 13
Samsung Galaxy A12 User Manual preview
Galaxy A12
Brand: Samsung Pages: 105

Brands by name

Popular brands

Load more brands