Maintenance strategy
Protocols
34
Maintenance Procedures
December 2003
Layer-1 protocols
Layer-1 protocols are used between the terminal or host DTE and the DCE, used between the DCE
equipment and the system port, and used inside the system.
The following Layer-1 protocols are used between the DTE equipment and the DCE equipment. DCE
equipment can be data modules, modems, or Data Service Units (DSUs). A DSU is a device that
transmits digital data to a particular digital endpoint over the public network without processing the data
through any intervening private network switches.
•
RS-232 — A common physical interface used to connect DTE to DCE. This protocol is
typically used for communicating up to 19.2 kbps.
•
RS-449 — Designed to overcome the RS-232 distance and speed restrictions and lack of modem
control
•
V.35 — A physical interface used to connect DTE to a DCE. This protocol is typically used for
transmissions at 56 or 64 kbps.
The following protocols are used at Layer 1 to govern communication between the DCE equipment and
the port. These protocols consist of codes inserted at the originating DCE and stripped at the port. The
DS1 protocol can be inserted at the originating, outgoing trunk port and stripped at the destination port.
•
Digital Communications Protocol (DCP) — A standard for a 3-channel link. This protocol sends
digitized voice and digital data in frames at 160 kbps. The channel structure consists of two
information (I) channels and one signaling (S) channel. Each I channel provides 64 kbps of voice
and/or data communication, and the S channel provides 8 kbps of signaling communication
between the system and DTE equipment. DCP is similar to ISDN BRI.
•
Basic Rate Interface (BRI) — An ISDN standard for a 3-channel link, consisting of two 64-kbps
bearer (B) channels and one 16-kbps signaling (D) channel.
•
Primary Rate Interface (PRI) — An ISDN standard that sends digitized voice and digital data in
T1 frames at 1.544-Mbps or, for countries outside the United States, in E1 frames at 2.048-Mbps.
Layer 1 (physical), layer 2 (link), and layer 3 (network) ISDN-PRI protocols are defined in
DEFINITY Communications System and System 75/85 DSE/DMI/ISDN PRI Reference Manual.
At 1.544 Mbps, each frame consists of 24 64-kbps channels plus 8 kbps for framing. This
represents 23 B channels plus 1 D channel. The maximum user rate is 64 kbps for voice and data.
The maximum distances are based on T1 limitations. At 2.048 Mbps, each E1 frame consists of
32 64-kbps channels.
•
Analog — A modulated voice-frequency carrier signal
•
ADU Proprietary — A signal generated by an ADU. The signal is for communication over
limited distances and can be understood only by a destination ADU or destination system port
with a built-in ADU
•
Digital Signal Level 1 (DS1) — A protocol defining the line coding, signaling, and framing used
on a 24-channel line. Many types of trunk protocols (for example, PRI and 24th-channel
signaling) use DS1 protocol at layer 1.
•
European Conference of Postal and Telecommunications rate 1 (CEPT1) — A protocol defining
the line coding, signaling, and framing used on a 32-channel line. Countries outside the United
States use CEPT1 protocol.
Summary of Contents for CMC1
Page 1: ...Maintenance Procedures 555 245 103 Issue 1 1 December 2003 ...
Page 14: ...Contents 14 Maintenance Procedures December 2003 ...
Page 416: ...Additional maintenance procedures IP Telephones 416 Maintenance Procedures December 2003 ...
Page 426: ...Index X 426 Maintenance Procedures December 2003 ...
