Avaya IP500 Installation Manual Download | Manualshive

Page: 110 / 442

background image

Installing IP500/IP500 V2

Page 110

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

5.6 Disable Unused Trunks

Each IP Office trunk card provides a fixed number of trunk ports with digital trunk ports supporting a fixed number of
digital channels. By default the IP Office configuration will have settings for all the possible trunks and channels.

In cases where the number of trunks or trunk channels in use or licensed is lower than the number supported by the trunk
card, the unused trunks and channels must be disabled.

·

Failure to do this will cause problems with outgoing calls. For example, on a system with an ATM4 trunk card

fitted but only two analog trunks actually connected, failure to disable the other two trunks within the IP Office
configuration will cause 50% of outgoing call attempts to fail. This is because the system cannot automatically
detect the service status of individual analog trunks.

·

For IP Office Release 8.1 Feature Pack 1 and higher with IP500 Analog Trunk 4 V2 cards and ATM4
Combination V2 cards, the system can detect with analog trunks are connected and so can automatically treat
unconnected trunk ports as out of service.

·

!

WARNING

This process requires the IP Office system to reboot in order to complete the changes. The reboot ends any current
calls and services.

To disable unused trunks:

1.

Start IP Office Manager

and receive the configuration from the IP Office system.

2. Within the IP Office configuration, select

Line.

3. For each line, set those lines or channels that are not connected or being used as out of service. The location of the

relevant setting varies for each trunk type.

·

Analog Trunks
To disable the whole trunk, on the main form set the Admin option to Out of Service.

·

BRI, E1 PRI, S0 and QSIG Trunks
To disable the whole trunk, on the main form set the Admin option to Out of Service. Otherwise set the
number of channels to match the actual subscribed channels.

70

«
...
108
109
110
111
112
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Samsung Pages: 287

Brand: Panasonic Pages: 100

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 112

Brand: Samsung Pages: 24

Brand: Collage Investments Pages: 34

Brand: Audiovox Pages: 137

Brand: Alcatel Pages: 73

OneTouch Conquest

Brand: Alcatel Pages: 349

Brand: EMPORIA Pages: 2

Brand: Chima Pages: 105

Brand: Amplicomms Pages: 90

Brand: HTC Pages: 16

Brand: NUU Mobile Pages: 16

Brand: Linear Pages: 8

Brand: Samsung Pages: 127

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands