Avaya IP500 Installation Manual Download | Manualshive

Page: 168 / 442

background image

Installing IP500/IP500 V2

Page 168

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

8.8 Swapping Extension Users

Whilst the example below shows 2 users swapping extensions the method can be used to swap multiple users within the
configuration and effecting the swaps after a single merge of the configuration changes.

Swapping Extension Users

For this example User A (202) and User B (203) want to swap extensions.

1. Load the IP Office configuration and select

Extension.

2. Locate the extension with the Base Extension set to 202, ie. matching User A's extension number.

·

If the group pane is visible (View | Group Pane) in IP Office Manager, it shows the extension details (ID,
Module, Port and Base Extension).

3. Select that extension and change its Base Extension setting to 203, ie. to now match User B's extension number.

If IP Office Manager is set to validate edits, it will warn that this change conflicts with the existing Base Extension
setting of another extension. Ignore the warning at this stage. Click OK.

4. Locate the other extension with the Base Extension set to 203, ie. matching User B's extension number.

5. Select that extension and change its Base Extension setting to 202, ie. to now match User A's extension number.

If the error pane is visible (View | Error Pane), the warnings about extension conflicts should now disappear.
Click OK.

6. Save the configuration back to the IP Office system.

7. At each of the extensions dial the log out short code set on the IP Office system. By default this is *36.

·

If any of the users is set to Forced Login, they will have to complete the login process at their new extension
using their Login Code.

«
...
166
167
168
169
170
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Warner Telecom Group Pages: 4

Brand: Samsung Pages: 38

Brand: Yealink Pages: 3

Brand: Samsung Pages: 155

Brand: Starmobile Pages: 53

Brand: Micromax Pages: 22

Brand: Grandstream Networks Pages: 10

Clarity Series BG1200-G

Brand: Transense Pages: 14

Brand: iData Pages: 38

Brand: Plum Pages: 21

Brand: Shenzhen Pages: 57

Brand: NEFFOS Pages: 69

Brand: Allworx Pages: 6

Brand: ICON Pages: 8

Brand: T-Mobile Pages: 59

Brand: Samsung Pages: 113

Brand: Samsung Pages: 201

Brand: Samsung Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands