Avaya IP500 Installation Manual Download | Manualshive

Page: 172 / 442

background image

Installing IP500/IP500 V2

Page 172

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

8.9.3 Rack Mounting Barrier Boxes

Where more than 3 Phone Barrier Boxes are used they must be rack mounted. The Barrier Box Rack Mounting Kit (SAP
Code 700293905) supports up to 8 Phone Barrier Boxes.

1. Unscrew the two screws arranged diagonally at the front of each barrier box and use these same screws to reattach

the barrier box to the rack mounting strip.

2. Each barrier box is supplied with a solid green ground wire connected to its functional ground screw. Remove and

discard this wire. Connect a green/yellow ground wire to the protective earth screw in the center of the Point on the
back of the Barrier Box.

3. The rack mounting strip has threaded M4 earthing pillars. Connect the other end of the barrier box ground wire,

using M4 washers and nuts, to the earthing pillar on that side of the rack mounting strip.

4. Using 14AWG wire with green and yellow sleeve, connect one of the earthing pillars to the buildings protective

earth.

5. Using 14AWG wire with green and yellow sleeve, connect the other earthing pillar to the Phone module.

6. Ensure that the following wires are not routed together in the same bundle:

·

Earth lead from the barrier box to the Phone module.

·

Internal wires, e.g. wires going directly to the Phone module.

·

Wires from external telephone going directly to the barrier boxes.

«
...
170
171
172
173
174
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: QMobile Pages: 66

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

Yealink SIP-T28P

Brand: Yealink Pages: 10

Yealink SIP-T28P

Brand: Yealink Pages: 2

Brand: Yealink Pages: 4

Yealink SIP-T28P

Brand: Yealink Pages: 2

Yealink SIP-T28P

Brand: Yealink Pages: 4

Brand: Yealink Pages: 158

Brand: Yealink Pages: 6

Brand: Yealink Pages: 4

Brand: Yealink Pages: 16

Brand: Yealink Pages: 73

Brand: Yealink Pages: 120

Brand: Yealink Pages: 2

Brand: TCL Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands