Avaya IP500 Installation Manual Download

Page: 175 / 442

Installing IP500/IP500 V2

Page 175

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

Additional Processes: So8 BRI Module

8.11.2 Example 2: Video Conference

In this example, calls are routed to a Polycom Viewstation module connected to a S0 port of the IP Office system.

The following settings were used on 4 incoming data channels of a PRI line:

Line Number: 5

Channel Allocation: 23 -> 1

Switch Type: 5ESS

Line Sub Type: PRI

Provider: AT&T

Channels: 1-4

Incoming Line Group: 95

Outgoing Line Group: 95

Direction: Bothway

Bearer: Data

Service: Accunet (this is a important)

Admin: In Service

To route an incoming video call on the PRI lines configured above to an SO8 module requires the following:

1. Create a dial short code that has the SO port as its destination Line Group. For this example the following was used:

· Short Code: 1500

· Number: .

· Feature: Dial

· Line Group: 601 (the SO8 port number)

2. Create an Incoming Call Routing that routes the appropriate calls to that short code. For this example the following was

used:

· Line Group: 95 (identifies calls using the PRI lines configured above)

· Destination: 1500 (the short code created above)

· Bearer: Any

To allow the video device on the S0 port to make outgoing calls to the PRI lines also requires a short code.

1. For this example the following was used:

Code: 91N;

Number: N

Feature: Dial

Line Group: 95

Summary of Contents for IP500



























































































































































































































































































































































































































































Search results

Summary of Contents for IP500

Reviews:

Related manuals for IP500

Brands by name

Popular brands

Avaya IP500, Installation Manual

Search results

Summary of Contents for IP500

Reviews:

Related manuals for IP500

Brands by name

Popular brands