Avaya IP500 Installation Manual Download | Manualshive

Page: 177 / 442

background image

Installing IP500/IP500 V2

Page 177

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

Additional Processes: So8 BRI Module

8.12 SNMP

SNMP (Simple Network Management Protocol) is a standard network protocol that allows the monitoring and management
of data devices across a network. An SNMP agent can be built into network devices such as routers and hubs. An SNMP
manager application, for example CastleRock or HP OpenView, can then communicate with those devices.

IP Office 2.0 and above supports SNMP communication. This communication can be:

·

Polling:
Some SNMP applications (called "managers") send out polling messages to the network. They then record the
responds of any SNMP enabled devices (called "agents"). This allows the application to create a network map and to
raise an alarm when devices previously present do not respond.

·

Most SNMP manager applications can also do simple IP address polling to locate non-SNMP enabled devices.
However this method of polling does not identify the device type or other information.

·

SNMP polling including details about the responding device. For example an IP Office control unit's response
includes the control unit type, level of software, routing table information, up time, etc.

·

Traps:
When certain events occur, a devices SNMP agent can send details of the event to the SNMP manager. This is called
an SNMP 'trap'. These appear in the event log of the SNMP manager. Most SNMP managers can be configured to
give additional alerts in response to particular traps.

·

Management:
Some SNMP agents support device management and configuration changes through the SNMP manager interface.
This is not supported by IP Office.

IP Office SNMP operation has been tested against Castle Rock SNMPc-EE 5.1.6c and HP OpenView Network Node Manager
6.41.

What Information is Available Via SNMP

As described above, SNMP information can either be polled by the SNMP application or received as the result of the IP
Office sending SNMP trap information.

While the .mib files should not be edited, they can be read using a text editor and contain descriptions of all the various
information objects that can be polled or sent and the information tha each object will include. For a list of the .mib files,
see

Installing the IP Office MIB Files

. The NOTIFICATION-TYPE objects are those used for

SNMP traps

, the other

types of objects are those that can be

polled

.

178

180

180

«
...
175
176
177
178
179
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: NTT docomo Pages: 68

Brand: Yealink Pages: 21

Brand: Kosher Pages: 19

Brand: PCD Pages: 73

Brand: G'Five Pages: 6

Brand: Spice Pages: 21

Brand: iPECS Pages: 2

SIP DECT Series

Brand: Teledex Pages: 1

Brand: Zte Pages: 99

Brand: Honeywell Pages: 25

Notifier FirstCommand Series

Brand: Honeywell Pages: 96

Brand: NEC Pages: 47

Brand: Avvio Pages: 30

Brand: Zte Pages: 172

Brand: Aastra Pages: 121

Brand: BOLTE Pages: 13

Brand: VK MOBILE Pages: 54

Brand: Nokia Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands