Avaya IP500 Installation Manual Download | Manualshive

Page: 198 / 442

background image

Installing IP500/IP500 V2

Page 198

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

9.7 Check the CPU LED

During normal operation, the CPU LED on the rear of the IP500 control unit
should be green.

·

Note
New IP Office 500 control units are supplied with a base software level
of 4.0.0. The CPU LED on these units will flash red until the unit is
upgraded to the required level of released IP Office core software.

Normal Power On Sequence
When power to the control unit is switched on, the normal sequence for the
CPU LED is as follows.

1. Steady Red for 3 seconds

2. Off for 10 seconds

3. Flashing alternate red/green for 4 seconds.

4. The LED should be steady green following successful start up. Note that

the IP500 cards on the front of the control unit may still be going
through their own start up process.

·

Flashing RED
A flashing red CPU LED at this stage indicates an error. The most
likely cause is a missing Feature Key card.

«
...
196
197
198
199
200
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Yealink Pages: 87

SPH-A600 Series

Brand: Samsung Pages: 111

Xperia ZL2 Sol25

Brand: AU Pages: 2

Brand: Docomo Pages: 194

Brand: Mitel Pages: 60

Comfort Pro P100

Brand: T-Comfort Pages: 148

OneTouch Conquest

Brand: Alcatel Pages: 349

COMfortel D-400

Brand: Auerswald Pages: 16

Brand: Doogee Pages: 39

Brand: AU Pages: 96

Shuttle CDM8964VM

Brand: UTStarcom Pages: 39

Brand: Samsung Pages: 340

Brand: Samsung Pages: 218

Brand: Zte Pages: 36

Brand: QTek Pages: 190

Brand: Nokia Pages: 29

Brand: Zte Pages: 25

Brand: Unitech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands