Avaya IP500 Installation Manual Download | Manualshive

Page: 264 / 442

background image

Installing IP500/IP500 V2

Page 264

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

10.9 IP400 Expansion Modules

The following IP400 external expansion modules are supported by IP Office Release 9.0 and can be used with an IP500
and IP500 V2 control units. Each module uses an external

power supply unit

supplied with the module. A locale

specific

power cord

for the PSU must be ordered separately.

If being rack mounted these units use the IP400 rack mounting kit. If being rack mounted, these units use the IPO IP500
RACK MNTG KIT. They cannot be wall mounted.

·

IP400 Analog Trunk Module (ATM16)

Provides an additional 16

ANALOG

ports for connection of analog trunks.

Supports both loop-start and ground-start trunks.

·

Available in a number of variants for different locales.

·

Use with ground start trunks requires that the trunk module and the IP
Office control unit are grounded.

·

IP400 Digital Station Module

Provides, depending on the variant, an additional 16 or 30

DS

ports for

supported Avaya digital phones. This module has been superseded by the
Digital Station V2.

·

IP400 Digital Station Module V2

Provides, depending on variant, an additional 16 or 30

DS

ports for

supported

Avaya digital phones

. Supersedes the previous Digital Station

module.

·

IP400 Phone Module

Provides, depending on variant, an additional 8, 16 or 30

POT

ports for

analog phones. This module has been superseded by the Phone Module V2.

·

IP400 Phone Module V2

Provides, depending on variant, an additional 8, 16 or 30

PHONE

ports for

analog phones. Supersedes the previous Phone module. With IP Office 3.1,
the Phone V2 supports a wider range of message waiting indication (MWI)
options than Phone V1 modules.

·

With V2 units, the labeling of analog phone ports was changed from POT to
PHONE.

39

40

266

390

270

393

268

393

48

274

398

272

398

«
...
262
263
264
265
266
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: WatchOvers Pages: 10

Brand: Xblue Networks Pages: 98

Brand: Panasonic Pages: 100

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 112

Brand: Audiovox Pages: 18

Brand: Avaya Pages: 6

Brand: Samsung Pages: 127

Brand: IPRO Pages: 23

Brand: Sigma Pages: 16

Brand: LG Pages: 81

Brand: LG Pages: 2

Brand: LG Pages: 78

Brand: LG Pages: 128

Brand: LG Pages: 2

Brand: LG Pages: 113

Brand: LG Pages: 114

Brand: LG Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands