Avaya IP500 Installation Manual Download | Manualshive

Page: 338 / 442

background image

Installing IP500/IP500 V2

Page 338

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

10.11.53 Audio Conferencing Unit

Avaya M and T-Series phones are supported by IP Office Release 7.0 and higher on an IP500 V2. They can be connected
to digital station ports provided by an

IP500 TCM8 base card

,

DS16A/DS30A external expansion module

or

DS16B/

DS30B external expansion module

.

The Audio Conferencing Unit (ACU) is a multiple microphone desktop conferencing unit. The Audio Conferencing unit only
supports the following Feature codes:

·

Speeddial: Feature 0
This feature code can be used to dial a stored number.

·

If Feature 0 is followed by a 3-dight number in the range 000 to 255, the system directory entry with the
matching index is dialed.

·

If Feature 0 is followed by * and a 2-digit number in the range 71 to 94, the personal directory entry with the
matching index is dialed.

·

Hold/Switch Calls: Feature 2
This feature code will hold the current call. If there was already a call on hold, the feature code will switch between
calls.

·

Conference: Feature 3
If the Audio Conferencing Unit has a call connected and another call on hold, using this feature code will conference
the unit and those calls.

·

Last Number Redial: Feature 5
When the phone is idle, this feature code can be used to redial the last number dialed from the Audio Conferencing
Unit.

231

247

250

«
...
336
337
338
339
340
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Yealink Pages: 6

T48G-SKYPE FOR BUSINESS EDITION

Brand: Yealink Pages: 12

Brand: Yealink Pages: 4

Brand: Yealink Pages: 16

Brand: Yealink Pages: 12

Brand: Yealink Pages: 3

Brand: Yealink Pages: 4

Brand: Yealink Pages: 8

Brand: Yealink Pages: 3

Brand: Yealink Pages: 4

Brand: Yealink Pages: 7

Brand: Yealink Pages: 2

Brand: Yealink Pages: 4

T48S Skype For Business Edition

Brand: Yealink Pages: 9

T48S Skype For Business Edition

Brand: Yealink Pages: 3

Brand: Yealink Pages: 32

Brand: Yealink Pages: 1126

Brand: Yealink Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands