Avaya IP500 Installation Manual Download | Manualshive

Page: 359 / 442

background image

Installing IP500/IP500 V2

Page 359

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

System Components: Phone Add-Ons

10.12.4 DBM32

The maximum number of button module buttons supported, of any type, on a single system is

1024

.

The DBM32 add on provides an additional 32 twin-LED programmable buttons for 1416 phones. The units do not require
their own power supply connection as they draw power from the phone to which they are connected.

·

Up to 3 units can be connected in a chain from a single 1416.

·

Up to a maximum of 32 DBM32 units on the system.

Item

SAP Code

DBM32 BUTTON MODULE

700469968

Accessories

1600 SERIES BM32 CABLE - REPLACEMENT

700415581

1600 SERIES BM32 BOND BRIDGE - REPLACEMENT

700415599

1616/BM32 PLASTIC LABEL COVERS (20) – REPLACEMENT

700415672

1600 SERIES BM32 FLIP STAND - REPLACEMENT

700432800

Paper Labels

1616/BM32 PAPER DESI LABELS - PACKAGE OF 50 LABELS (8.5" x 11")

700415656

1616/BM32 PAPER DESI LABELS - PACKAGE OF 50 LABELS (A4)

700434236

·

Note for Australian installations only:

Installations of the 1416 terminal with an 1151 PSU and DBM32 must be restricted to the same building as the host
Gateway. That is, the 1416 – if installed with an 1151 PSU and DBM32 – cannot be connected in a campus
environment where the 1416 terminal is installed in a building separate from the building housing the Gateway.
This application cannot be used with exposed (out-of-building) wiring.

·

For installations in which the 1416 is used without the 1151 PSU and DBM32, campus connections are
acceptable: the 1416 can be located in a separate building in these cases.

·

This restriction applies to Australian installations only.

355

«
...
357
358
359
360
361
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Hama Pages: 12

Brand: TCL Pages: 35

Brand: Pantech Pages: 126

Brand: 101VOICE Pages: 2

Alltel Hue II SCH-R600 Series

Brand: Samsung Pages: 167

Brand: Aethra Pages: 56

Brand: Alcatel Pages: 36

Brand: Spice Pages: 26

Brand: bq Pages: 88

Brand: HTC Pages: 4

Brand: ATCOM Pages: 60

HANDLEPLUS 326I GSM

Brand: Doro Pages: 280

Brand: HTC Pages: 204

Brand: Alcatel Pages: 21

Brand: Ericsson Pages: 37

Brand: Aastra Pages: 163

Brand: Citizen Pages: 7

Brand: Commander Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands