Avaya IP500 Installation Manual Download | Manualshive

Page: 427 / 442

background image

Installing IP500/IP500 V2

Page 427

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

Safety Statements: Port Safety Classification

11.6 EMC Directive

889/336/ EEC (EMC Directive) CISPR 22:1993 including A1 + A2, AS/NZ 3548:1995 (ROW)

·

WARNING

This is a class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his or her own expense.

Canadian Department of Communications (DOC)

''NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does
not imply that Industry Canada approved the equipment."

EMC Caution for China

«
...
425
426
427
428
429
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Radio Shack Pages: 64

Brand: Handspring Pages: 2

Brand: palmOne Pages: 14

Brand: T-Mobile Pages: 174

Brand: Yealink Pages: 38

Brand: BenQ Pages: 97

Brand: Blackberry Pages: 30

Brand: Pantech Pages: 77

Brand: Videocon Pages: 28

Brand: NUU Mobile Pages: 16

Brand: Nokia Pages: 23

Brand: Nokia Pages: 121

Brand: Nokia Pages: 131

Brand: Lava Pages: 20

Brand: Huawei Pages: 65

Brand: Huawei Pages: 30

Brand: Huawei Pages: 74

Brand: Huawei Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands