Avaya IP500 Installation Manual Download | Manualshive

Page: 433 / 442

background image

Installing IP500/IP500 V2

Page 433

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

Safety Statements: Regulatory Instructions for Use

11.7.7 Compliance with FCC Rules

Transmit and Receive Gain Settings for PRI/T1 and Analog Ports

The Gain settings are password controlled for use by qualified installation personnel only and must not be made available
to the end user. The default gain settings of 0dB ensures compliance with FCC part 68 section 68.308(b)(5) and TIA/EIA-
IS-968 Section 4.5.2.5. "Through transmission amplification from ports for the connection of separately registered
equipment or from other network connection ports". Gain setting adjustment by unqualified personnel may result in
violation of the FCC rules. Qualified personnel may adjust gain settings above these levels only where:

1. Measurement is made to ensure that the power levels sent to line at each network interface connected does not

exceed the maximum levels specified in FCC part 68 section 68.308(b) and TIA/EIA-IS-968 Section 4.5 for that
specific interface type.

2. Where gain adjustment away from the default values are made, precautions should be taken to ensure that the

connection of terminal equipment is controlled by qualified installation personnel.

3. To conform with the Receive Objective Loudness Rating at distances greater than 2.7km from the central office, on

analog trunks a receive gain of 1.5dB must be set.

«
...
431
432
433
434
435
...
»

Summary of Contents for IP500



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP500

Brand: Neoi Pages: 40

Yealink SIP-T46G

Brand: Yealink Pages: 6

Brand: Yealink Pages: 176

Brand: Light Repute International Pages: 15

one touch Fire 4012X

Brand: Alcatel Pages: 31

Brand: Pantech Pages: 51

Brand: Nortel Pages: 160

Brand: Plum Mobile Pages: 15

2100-TPC Cellular 120v Tower

Brand: Rath Pages: 9

Brand: AU Pages: 86

Brand: HME Pages: 2

Brand: G'Five Pages: 6

Brand: ORANGE Pages: 88

Transform SPH-M920

Brand: Samsung Pages: 238

Brand: Samsung Pages: 203

VERIZON SCHU460

Brand: Samsung Pages: 193

Verizon Wireless Juke SCH-U470

Brand: Samsung Pages: 162

Brand: IPRO Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands