background image

 

P116T Stackable Switch Installation Guide 

1

 

 

Preface 

Important information  

SAFETY PRECAUTIONS 

CAUTION – TO REDUCE THE RISK OF ELECTRIC  SHOCK AND FIRE 

1.  All servicing should be undertaken ONLY by qualified personnel. The parts 

inside the unit CANNOT be serviced or repaired by the end user. Please call 
your service representative for assistance. 

2.  Do NOT plug in, turn on or attempt to operate a damaged unit. 
3.  Ensure that the chassis ventilation slots in the unit are NOT BLOCKED. 
4.  Replace a “blown” fuse only with the same type and rating as is marked on the 

safety label adjacent to the power inlet housing the fuse. 

5.  DO NOT operate the unit in a location where the maximum ambient 

temperature exceeds 40ºC. 

6.  Be sure to  unplug the power supply cord from the wall socket BEFORE 

attempting to remove and/or check the main power fuse. 

PRECAUTIONS DE SECURITÉ 

AVERTISSEMENT – POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE ET D’INCENDIE 

1.  Tout entretien doit être fait UNIQUEMENT par un personnel de service 

qualifié. Aucun élément ne peut être réparé par un particulier. 

2.  NE PAS brancher, allumer ou essayer de faire fonctionner une unité sur 

laquelle un doute existe quant à son bon fonctionnement. 

3.  S’assurer que les ouvertures d’aération du châssis dans l’appareil NE SONT 

PAS OBSTRUEES.. 

4.  Remplacer un fusible défaillant UNIQUEMENT par un modèle du même type 

suivant les recommandations indiquées sur l’étiquette de securité posée dans 
le logement du fusible. 

5.  NE PAS faire fonctionner l’appareil dans un endroit où la temperature dépasse 

les 40ºC. 

6.  S’assurer de débrancher l’alimentation électrique AVANT toute manipulation 

sur le fusible principal. 

SICHERHEITSVORKEHRUNG 

ACHTUNG – ZUR VERHINDERUNG DES RISIKOS VON ELEKTRISCHEM SCHLAG UND FEUER 

1.  Die Geräte enthalten keine Bauteile, die außerhalb des Avaya Servicezentrums 

gewartet oder repariert werden können. Die Wartung darf NUR von 
qualifiziertem, technischem Personal durchgeführt werden. 

2.  NIEMALS ein beschädigtes Gerät einschalten, oder versuchen es zu bedienen. 

Summary of Contents for P116T

















Reviews: