background image

Avem Quirks  

National Service Support Line: 

1800 658 120 

 

 

LogTag Temperature Recorder: 

 

The LogTag temperature recorder (pictured to the right) records vaccine 
temperature data over time 

 

 

Temperature is recorded from a probe inside the refrigerator cabinet, 
surrounded by transfer gel, providing a 

simulated vaccine core 

temperature. 

 

 

Temperature information is downloaded to a PC, using the 
LogTag Analyser software provided (see 

Setting up the LogTag  

on 

Page 7

). 

 

This information can be used in regulatory audits and insurance 
claims, to provide an accurate representation of vaccine core temperature inside the 
Medisafe refrigerator, during its operation. 

 

Temperature patterns are recorded over time, providing indication of damaged seals, 
or changes in operating temperature. 

 

The LogTag recorder must be connected to the PC immediately after it has been removed 

from the Medisafe for downloading, and reconnected to the Medisafe prior to starting,  otherwise 
false readings will result! 

 

DO NOT USE vaccines exposed to temperatures below +2°C or above +8°C, as recorded   by 

your LogTag, without obtaining further advice. Do not discard these vaccines. Isolate vaccines 
and  contact  the  State/Territory  health  authorities  for  advice  on  the  National  Immunisation 
Program  vaccines  and  the  manufacturer/supplier  for  privately  purchased  vaccines. 

Recommendations  for  the  discarding  of  vaccines  may  differ  between  health  authorities  and 
manufacturers

Do not discard any vaccines until you discuss the necessary actions. 

Summary of Contents for Medisafe





















Reviews: