background image

1.2    

SAFETY GUIDELINES

The KPD-TCP1US-8, 8-Button Wall Plate Control Keypad has been tested for conformance to safety regulations and 
requirements, and has been certified for international use. However, like all electronic equipments, the HBT2-C6BPOC-SET 
should be used with care. Read the following safety instructions to protect yourself from possible injury and to minimize the 
risk of damage to the unit. 

Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage
or other hazards.
Keep the device away from liquids.
Spillage onto the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on
to the housing, unplug the module immediately.
If the unit appears damagaed, have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

!

!

!

!

!

!

!

!

1.1    

IMPORTANT SAFEGUARDS

• Any product on which the serial number has been defaced, modified or removed.
• Damage, deterioration or malfunction resulting from:
• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to 

   follow instructions supplied with the product.

• Repair or attempted repair by anyone not authorized by us.
• Any damage of the product due to shipment.
• Removal or installation of the product.
• Causes external to the product, such as electric power fluctuation or failure.
• Use of supplies or parts not meeting our specifications.
• Normal wear and tear.
• Any other causes which does not relate to a product defect.
• Removal, installation, and set-up service charges.

Please read all of these instructions carefully before you use the device. Save this manual for future reference.

Avenview warranty certificate please refer to page #20

Warranty does not include:

SECTION 1 

: GETTING STARTED

Rev.00 12/2017

www.avenview.com

1

Summary of Contents for KPD-TCP1US-8

























Reviews: