background image

TECHNICAL SUPPORT

Disclaimer 

While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of 

Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this 

documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages 

in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein. 
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design. 

With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but 

not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.

AV Connectivity, Distribution And Beyond...

USA Head Office
Office Avenview 
Corp. 275 Woodward Avenue
Kenmore, NY 14217 
Phone: +1.716.218.4100 ext223
Fax: +1.866.387-8764
Email: info@avenview.com

Canada  Sales
Avenview
151 Esna Park drive, Unit 11 & 12
markham, Ontario, L3R 3B1
Phone: 1.905.907.0525 
Fax: 1.866.387.8764
Email: info@avenview.com

Avenview Europe
Avenview Europe
demkaweg 11
3555 HW  Utrecht
Netherlands
Phone: +31 (0)85 2100- 613
Email: info@avenview.eu

Avenview Hong Kong
Unit 8, 6/F., Kwai Cheong Centre, 
50 Kwai Cheong Road, 
Kwai Chung, N.T. 
Hong Kong
Phone: 852-3575 9585
Email: wenxi@avenview.com

Summary of Contents for SW-HBT4K-C6-4X4E









Reviews: