background image

Java Comp 150

 Owner’s Manual

CONTENTS

INTRODUCTION.........................................................................3

PLEASE NOTE............................................................................3

OPERATING LIMITS..................................................................4

SPECIFICATIONS.......................................................................4

RIGGING THE JAVA COMP......................................................5

PRE-FLIGHT CHECKLIST.........................................................8

FLYING THE JAVA COMP  ......................................................9

POST FLIGHT INSPECTION......................................................10

DE-RIGGING...............................................................................11

VB. (VARIABLE BILLOW)........................................................12

VB. MAINTAINANCE................................................................13

TUNING INSTRUCTIONS..........................................................13

BATTENS AND BATTEN PROFILE..........................................14

MAINTENANCE..........................................................................16

REPAIR........................................................................................18

RECOMMENDED COMPONENT LIFE.....................................18

TRANSPORTATION...................................................................18

SHORT PACKING.......................................................................19

TRANSPORTATION BY AIR.....................................................20

STORAGE....................................................................................21

TROUBLE SHOOTING...............................................................21

OWNERSHIP...............................................................................23

APPENDIX:

LOSING THE KINGPOST- THE DIFFERENCES......................25

ASSEMBLY DRAWINGS...........................................................27

CHECKING WASHOUT.............................................................30

3

Summary of Contents for JAVA COMP 150 Dacron



































Reviews: