background image

2

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow 
all instructions listed below, may result in electric shock, fire and/or 
serious personal injury.

1. Keep your work area clean and well lit. Cluttered benches and dark 
    areas invite accidents. Keep bystanders, children, and visitors away 
    while operating an inflator. Distractions can cause you to lose control.
2. Operate inflator in an open area at least 18 in. away from any wall or 
    object that could restrict the flow of fresh air to ventilation openings.

ELECTRICAL SAFETY

1. To reduce the risk of electrical shock, do not put inflator in water or 
    other liquid. Do not place or store appliance where it can fall or be 
    pulled into a tub or sink.
2. Use this product only with batteries and chargers.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when 
    operating an inflator. Do not use inflator while tired or under the 
    influence of drugs, alcohol, or medication. A moment of inattention 
    while operating inflator may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long 
    hair. Keep your hair, clothing, and gloves away from moving parts. 
    Loose clothes, jewelry, or long hair can be caught in moving parts.
3. Do not overreach. Keep proper footing and balance at all times. 
    Proper footing and balance enable better control of the inflator in 
    unexpected situations.
4. Use safety equipment. Always wear eye protection. Dust mask, 
    non-skid safety shoes, hard hat, or hearing protection must be used 
    for appropriate conditions.
5. Eye protection is required to guard against flying fasteners and debris 
    which could cause severe eye injury.

When using electric appliances, basic precautions should always 
be followed, including the following.

WORK ARER

Summary of Contents for ACAP110D


















Reviews: