background image

5

SAFETY PRECAUTIONS FOR INFLATOR

  4. Inspect unit for cracks, pin holes, or other imperfections that could 
      cause inflator to become unsafe. Never cut or drill holes in the inflator.
  5. Make sure the hose is free of obstructions or snags. Entangled or 
      snarled hoses can cause loss of balance or footing and may become 
      damaged.
  6. Use the inflator only for its intended use. Do not alter or modify the 
      unit from the original design or function.
  7. Always be aware that misuse and improper handling of this inflator 
      can cause injury to yourself and others.
  8. Never leave an inflator unattended with the air hose attached to the 
      item being inflated.
  9. Do not continue to use an inflator or hose that leaks air or does not 
      function properly.
10. Always disconnect the air supply and power supply before making 
      adjustments, servicing an inflator, or when an inflator is not in use.
11. Do not attempt to pull or carry the inflator by the hoses.
12. Always follow all safety rules recommended by the manufacturer of 
      your inflator, in addition to all safety rules for the inflator. Following 
      those rules will reduce the risk of serious personal injury. 

.

13. Household use only.
14. Do not use inflator as a breathing device.
15. Never direct a jet of compressed air toward people or animals. Take 
      care not to blow dust and dirt towards yourself or others. Following 
      this rule will reduce the risk of serious injury.
16. Protect your lungs. Wear a face or dust mask if the operation is dusty. 
      Following this rule will reduce the risk of serious personal injury.
17. Do not use this inflator to spray chemicals. Your lungs can be 
      damaged by inhaling toxic fumes.
18. Check damaged parts. Before further use of the inflator or air tool, a 
      guard or other part that is damaged should be carefully checked to 
      determine that it will operate properly and perform its intended 
      function. Check for alignment of moving parts, binding of moving 
      parts, breakage of parts, mounting, and any other conditions that 
      may affect its operation. A guard or other part that is damaged 
      

Summary of Contents for ACAP110D


















Reviews: