background image

AO16 Analog Output Card

12

Safety Compliance

Safety Statement

This equipment has been tested to comply with USA and Canadian safety 
certification in accordance with the specifications of UL Standards: UL60065 7th 
/IEC 60065 7th and Canadian CAN/CSA C22.2 60065:03. Avid Inc., has been 
authorized to apply the appropriate UL & CUL mark on its compliant equipment.

Warning

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this equipment near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the 
manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, 
or other equipment (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A 
polarized plug has two blades with one wider than the other. A grounding type 
plug has two blades and a third grounding prong. The wide blade or the third 
prong are provided for your safety. If the provided plug does not fit into your 
outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect power cords from being walked on or pinched particularly at plugs, 
convenience receptacles, and the point where they exit from the equipment.

11) Only use attachments/accessories specified by the manufacturer.

12) For products that are not rack-mountable: Use only with a cart, stand, tripod, 
bracket, or table specified by the manufacturer, or sold with the equipment. 
When a cart is used, use caution when moving the cart/equipment combination 
to avoid injury from tip-over.

13) Unplug this equipment during lightning storms or when unused for long 
periods of time. 

14) Refer all servicing to qualified service personnel. Servicing is required when 
the equipment has been damaged in any way, such as power-supply cord or 
plug is damaged, liquid has been spilled or objects have fallen into the 
equipment, the equipment has been exposed to rain or moisture, does not 
operate normally, or has been dropped.

15) For products that are a Mains powered device: 
The equipment shall not be exposed to dripping or splashing and no objects 
filled with liquids (such as vases) shall be placed on the equipment. 

Warning! To reduce the risk of fire or electric shock, do not expose this 
equipment to rain or moisture. 

16) For products containing a lithium battery: 
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only 
with the same or equivalent type. 

17) For products with a power switch: 
The main power switch should remain accessible after installation. 

18) The equipment shall be used at a maximum ambient temperature of 40° C.

Summary of Contents for AO16


















Reviews: