background image

Chapter 1: Introduction to the FC726

1

Chapter 1: Introduction to the FC726

The FC726 is a compact, 2U, digital-audio format converter that translates back and forth between MADI (Multichannel Audio 
Digital Interface) and the digital audio formats listed in the table below. AES/EBU outputs are always available, regardless of the 
formats being translated. The FC726 performs the highest quality sample-rate conversion (SRC) on all channels that require it. 

The FC726 includes the following features:

• Can apply different format conversion and/or SRC to each bank of eight channels.

• Automatically applies SRC when necessary but can be manually disabled.

• Performs format conversion and SRC on more channels (56) than other devices. 

• Each of the 56 channels is bidirectional.

• Supports 24-bit audio at a 96 kHz sample rate.

• Maintains compatibility with older devices by offering 16- or 20-bit dithering and supporting 96 kHz legacy standards.

The FC726 lets you transfer digital audio between incompatible devices, including:

• Mix down on a System 5 digital console at 24-bit 96 kHz with source material from a ProDigi or Sony tape machine at 48 kHz 

(automatic SRC).

• Transfer tracks from a Tascam DA-88, Sony 3348, or Alesis ADAT to a Euphonix R-1.

Digital audio formats supported by the FC726

Company/Organization

Format Name

Equipment Using Format

Transmission Medium

Audio Engineering
Society

MADI

Euphonix R-1, S-5; many large 
format digital consoles

BNC cable

AES/EBU  (AES-3)

Most DAT machines and stereo 
D/A devices, sound cards, 
effects processors 

Two balanced XLR 
cables

Tascam

TDIF-1 (Teac Digital 
Interface Format)

Tascam DA-88, DA-98, small 
format digital consoles and 
workstations

25-pin cable

Mitsubishi

ProDigi

Otari and Mitsubishi digital 
multitracks

Two 50-pin cables

Sony

SDIF-2

Sony 3324 and 3348

Two 50-pin cables

Summary of Contents for FC726





































Reviews: