background image

 

 
 

 
SPECIFICATIONS 

 

 

INGENIUM 

 

 

 

DRIVE BELT 

SPEEDS 

33 and 45 RPM 

PLATTER MASS 

2.5 Kg 

BEARING 

Inverted stainless steel 

THRUST POINT 

Tungsten carbide/Sapphire 

SUSPENSION 

Three point elastomer 

TONEARMS As 

ordered 

MOTOR 

115/230v 12mNm ac synchronous 

POWER SUPPLY 

Separate control unit 

VOLTAGE INPUT 

115-240vac 50/60Hz 5 watts max. (depending on region) 

 

 

DIMENSIONS  (overall) 

See website for individual model size 

 

 

NET WEIGHT 

5.0 - 9.0Kg (depending upon model)  

 

 

 

PACKAGING 

54 - 74 x 36 x 22cm (depending upon model) 

SHIPPING WEIGHT 

8.0 - 14.0Kg (depending upon model) 

 

AVID reserves the right to improve or change its products without notice at any time. 

 

 

 

 

 

 

EC Declaration of Conformity 

22 December 2012 

We declare that the INGENIUM conforms to directives and harmonized international standards 

LVD (73/23/EEC) Low voltage directive 

EMC (89/36/EEC) Electromagnetic conformity 

BS EN 60065: 1994  Safety requirements for mains operated electronic and related apparatus for household and similar use    

CENELEC HD21/22    Flexible cables and cords 

 

EN 55020: 1988       Electromagnetic Immunity 

 

EN 55013: 1990       Electromagnetic Emissions 

 

 

 

 

C. Mas 

Director

 

AVID HIFI Limited 

 

 

Summary of Contents for Ingenium Series








Reviews: