background image

 

Abnormal Procedures

    5-9

 

 

 

 

TOTAL LOSS OF PFD (SINGLE PFD EQUIPPED AIRCRAFT) 

Failure Indication: 

A total failure of the PFD is indicated by both the display and 
bezel buttons all blank/unlit. 

Functionality Lost: 

A loss of the PFD will result in a complete loss of autopilot 
functionality. 

Recommended Pilot Action: 

Immediately transition to hand-flying via the standby instruments 
and seek VMC as soon as feasible. 

Consider attempting a single PFD warmstart by cycling both PFD 
circuit breakers for less than 20 seconds. A successful warmstart 
will restore all PFD and autopilot functionality. 

 

TOTAL LOSS OF PFD (DUAL PFD EQUIPPED AIRCRAFT) 

Failure Indication: 

A total failure of a PFD is indicated by both the display and bezel 
buttons all blank/unlit on the problem PFD 

and a “No Comm With 

(Co)Pilot PFD” yellow alert box on the functional PFD.  If the 
cockpit ADAHRS source selection switch was set to the PFD that 
experience the failure, the autopilot will automatically disconnect 
and provide the disconnect aural tones. 

Functionality Lost: 

As soon as the cockpit ADAHRS source selection switch is set to 
the fully functional PFD, there is no loss of any autopilot 
functionality. 

Recommended Pilot Action: 

Manually set the cockpit ADAHRS source selection switch to the 
fully functional PFD and then re-engage the autopilot in the 
desired modes. 

Change 2 

Summary of Contents for DFC90




























































































Reviews: