background image

Crosscheck Monitor

Entegra EXP5000 PFD

-60-

600-00157-000 Rev. 06

4.3 Crosscheck Monitor

Figure 16. Crosscheck Monitor

The Envision EXP5000 comes equipped with a self-check monitor. 
When this monitor detects a condition that does not warrant removal 
of data, a CROSSCHECK ATTITUDE warning message displays. 

When this message is displayed, scan all backup instruments and 
auxiliary instruments (backup attitude indicator, backup airspeed 
indicator, and back up altimeter) to crosscheck the aircraft attitude. 
The warning message is automatically removed when the self-check 
monitor confirms the EXP5000  attitude is valid.  

The message will not be displayed when air data is invalid (as shown 
on page 58). Cross referencing the EXP5000 attitude to the backup 
ADI is recommended during flight with invalid air data.

For aircraft equipped with a 55X autopilot, if a CROSSCHECK 
ATTITUDE alert displays on the PFD, Avidyne strongly 
recommends using Autopilot (not HDG mode).

Note

: Highly dynamic maneuvering such as multiple linked lazy-8 leaves 

may result in small pitch and/or bank errors. If the errors build up to an 
excessive amount, the crosscheck attitude message may display.

Note:

 In dual PFD installations, the CROSSCHECK ATTITUDE message 

applies to the selected ADAHRS source.

Summary of Contents for Envision EXP5000



























































































Reviews: