Appendices
Page 60
APPENDIX C: Jacq3G Module Troubleshooting and Adjusting Guide (continued)
Test #7: Observe the misbehaving hook in action. Is it frequently crossing over/under with a neighboring hook? Does it have abnormal
movement side-side or front-back as it slides up and down through the guides? If so, it or possibly the adjacent hook is bad.
Test #8: Observe the hook in action and listen carefully. Are the hooks vibrating significantly on this module than on others? Are you hearing
squeaking? The hooks and/or slide bearings need lubrication.
Test #9: Compare upper and lower knives on all modules at open shed with all hooks down. Are they the same heights and angles? An
observable angle difference is a red flag, which must be corrected immediately or it will result in bearing failure. Small variations in knife heights
of less than ¾” are not of concern. Larger knife height variations mean that you have a knife alignment issue.
If you pass these tests but still have a problem, you have a solenoid bar placement issue.
Equipment Fixes
Solenoid bar placement: Incrementally adjust/test the solenoid mount bar until issue goes away. Incremental adjustment is typically ½-1 turn of
the nut; test with tabby with alternately activates the upper and lower solenoid bars. Adjustment can be made independently at front and back
hardware, however it is a good idea to loosen both front and back before making the adjustment to avoid binding/bowing of the solenoid bar.
Pick the side that is closest to the bad hook. If the bad hook is relatively centered, adjust both sets of hardware. Adjust the solenoid mount bar
away from the knife if the hook is lifting when it should not; in when the hook does not lift.
Bad solenoid: Replace the bad solenoid. Note that when pulling the electrical wires from the black plastic connector; gently pry out the tab in the
connector with a pin to release the solenoid wire. CAUTION: Make sure you do not accidentally drop the plunger spring onto the printed circuit
boards while it is powered or you risk shorting the printed circuit board.
Summary of Contents for TECHNICAL EDUCATION LOOM
