background image

 

14 

7. Technical Information 

 
Sensitivity Cinch: 

 

 

 

1.2 V / 10 kOhms (400 W / 4 Ohms) 

Sensitivity XLR:  

 

 

 

1.2 V / 20 kOhms (400 W / 4 Ohms) 

Gain 

 

 

 

 

 

30 dB 

 
Output Power into 8 Ohms: 

 

 

>220 Watts 

Output Power into 4 Ohms: 

 

 

>450 Watts 

Output Power into 2 Ohms: 

 

 

>650 Watts 

 
Intermodulation 25 W / 4 Ohms:  

 

< 0.01% 

THD at 25 W / 4 Ohms:  

 

 

< 0.005% 

Transient intermodulation (TIM): 

 

not measurable 

Signal-to-noise-ratio (SNR) 25 W / 4 Ohms: 

> 100 dB(A) 

Frequency response:   

 

 

0.3 Hz - >400 kHz 

Load band width 25 W / 4 Ohms: 

 

0.3 Hz - >400 kHz 

Rise time at 4 Ohms:   

 

 

µ

Slew rate: 

 

 

 

 

> 200 V / 

µ

 
Damping factor (8 Ohms): 

 

 

> 1000 

 
Power supply:   

 

 

 

230 V or 115 V / 50/60 Hz / 3500 VA max 

Operation without signal: 

 

 

150 VA 

Stand by: 

 

 

 

 

<1 VA 

Dimensions (L x W x H): 

 

 

420 mm x 432 mm x 253 mm 

Weight:  

 

 

 

 

42 kg 

 
Issued October 2013 
 
We reserve the right to amend technical details and fittings in case of product improvements 

Summary of Contents for OVATION SA8.2















Reviews: