background image

 

(6

 USE 

 

Push button

  

 

a. 

Press the button “Stop”, the motor is stopped then. 

b. 

Press the button “Low”, the motor is running at low speed. 

c. 

Press the button “Mid”, the motor is running at medium speed. 

d. 

Press the button “High”, the motor is running at high speed. 

e. 

Press the button “Lamp”, both lamps start shining .Press the button 
again; the lamps are switched off then.  

 

 

 
 

(7)  MAINTENANCE 

 

Clean the filters as below: 

 

 

The filter mesh is made of metal. Do not use corrosive detergent on 
it.   

 

Keeping this filter clean will keep the appliance running correctly. 
Strictly follow the guidelines below. 

 

Method 1: Put the mesh into 40-50 c clean water, pour on detergent, 
and soak for 2-3 mins. Wear gloves and clean with a soft brush. Do 
not apply too much pressure, as the mesh is delicate and will 
damage easy. 

 

Method 2: If instructed to do so, it can be put into a dishwasher, set 
the temperature at around 60 degrees.  

 
Clean the range hood as below: 

 

 

To protect the main body from corrosion over a long period of time, 
the range hood should be cleaned with hot water plus non corrosive 
detergent every two months. 

 

Do not use abrasive detergent as they will damage the body. 

 

Keep the motor and other electrical parts free from water, as this 
will cause damage to the appliance. 

Summary of Contents for PPS6031













Reviews: