background image

EN 

USE

 

A

B

C

D

E

F

G

H

Control panel 

Button

 

Function

 

Display

 

A

 

Turns the suction motor on and off at speed one. 

Displays the set speed 

B

 

Decreases the working speed. 

Displays the set speed 

C

 

Increases the working speed. 

Displays the set speed 

D

 Activate 

intensive

 speed from any other speed, 

including motor off. This speed is set to operate 
for 6 minutes, after which the system returns to the 
speed that was set before. Suitable to deal with 
maximum levels of cooking fumes. 

Displays 

HI

 and the time remaining once 

e

very second. 

Press and hold the button for approximately 5 
seconds, with all the loads turned off (Motor and 
Lights), to turn the Activated Charcoal Filter 
alarm On and Off. 

FC

+

Dot

 (2 flashes)–Alarm On. 

FC

+

Dot

 (1 flash)–Alarm Off. 

E

 

24H function 

Turns the suction motor on at speed one 
and effects one 10 minute

s

 extraction every hour.  

Displays 

24

 and the 

dot

 at the bottom right flashes once 

every second, while the motor is running. 
It is disabled by pressing the button. 

When the filters alarm is triggered, the alarm can 
be reset by pressing and holding this button for 
approximately 3 seconds.  
These indications are only visible when the motor 
is turned off. 

FF

 flashes three times. 

When the procedure terminates, the indication shown 
previously turns off: 

FG

  indicates the need to wash the metal grease filters. 

The alarm is triggered after the Hood has been in 
operation for 100 working hours.  

FC

  indicates the need to change the activated charcoal 

filters, and also to wash the metal grease filters. The alarm 
is triggered after the Hood has been in operation for 200 
working hours. 

F

 

Delay function 

 

Activate automatic switch-off with a 30’ delay. 
Suitable to complete elimination of residual 
odours. Can be activated from any 

speed

, and is 

disabled by pressing the button or turning the 
motor off. 

Displays the operating speed and the 

dot

 at the bottom 

right flashes once a second. 

Press and hold the button for approximately 5 
seconds, with all the loads turned off (Motor and 
Lights), to 

activate

 the Remote Control

.

IR

+

Dot

 (2 flashes)–Alarm On. 

IR

+

Dot

 (1 flash)–Alarm Off. 

G

 

Turns the lighting system on and off at maximum 
intensity. 

H

 

Turns the Courtesy Lighting on and off. 

Summary of Contents for PPS902SI













Reviews: